Skip to content
Omnikalc

Standard hook development length (ldh) calculator

Enter the bar size, the steel and concrete strengths and the hook details to get the development length of a standard hook, the tail extension, the minimum bend diameter and the effect of the factors.

Updated on
Your inputs
in

Value out of range

psi

Value out of range

psi

Value out of range

Results

Development length of the hook (with the minimum)

14.2 in

Basic development length
14.2 in
Development length with the factors
14.2 in
Extension of the tail
9.0 in
Minimum inside diameter of the bend
4.5 in

The standard hook development length calculator gives the development length ldh of a deformed bar with a 90 or 180 degree hook in tension, with the modification factors, the minimum length, the tail and the minimum bend diameter.

How the calculation works

  • Enter the bar diameter, the steel and concrete strengths and the type of hook.
  • Choose the concrete type, the coating, the cover and the confinement factors.
  • The calculator gives the basic development length, the length with the factors, the governing length with the minimum, the tail and the bend diameter.

Example

A #6 bar (0.75 in) of Grade 60 in 4,000 psi normal weight concrete, uncoated, with a standard 90° hook. The basic length is 0.02 × 60,000 / √4,000 × 0.75 = 14.2 in. The minimum of 8 db = 6 in and 6 in is lower, so the hook development length is 14.2 in, with a tail of 9 in and an inside bend diameter of 4.5 in. If the bar is epoxy coated, with good cover and ties, the factors 1.2 × 0.7 × 0.8 give 9.6 in, and the minimum 6 in is not governing.

Why it matters

The calculator helps detailers, structural engineers, contractors and students to size the anchorage of beam bars in columns and walls, corbels and footings where there is no room for a straight bar, and to see how the factors change the length.

Good to know

The development length of the hook is measured from the critical section to the outside edge of the bar at the bend, not to the end of the tail. Where the column is too narrow for the hook, use a smaller bar, a higher strength of concrete or a headed bar. Epoxy coated bars need 20 % more. Keep the hook inside the column core, away from the cover, and check the congestion of the joint. For seismic frames, the hook for the joint of a special moment frame has its own length, which is longer than the one here.

The rebar development length calculator gives the anchorage of straight bars and lap splices, the shear friction calculator checks a joint, the reinforced concrete beam calculator gives the flexural capacity and the anchor bolt pullout calculator checks an anchor.

Frequently asked questions

What is the development length of a hook?

A standard hook (a 90 or 180 degree bend with a straight tail) lets a bar in tension anchor in a short distance, such as the end of a beam in a column or a corbel. The development length ldh is measured from the critical section to the outside of the bend, and it is much shorter than the straight bar length.

What is the formula?

In ACI 318-11, ldh = 0.02 ψe λ fy db / √f'c for the basic length, with the coating factor ψe and the lightweight factor, then multiplied by 0.7 for the cover and 0.8 for the confinement when these apply. The result must not be less than 8 db or 6 in. The newer editions of ACI 318 have a different expression with more factors, so check the edition of your code.

Does the hook help in compression?

No. A hook is not effective in compression, so a hooked bar is not credited in compression. The development length of the hook is for the bar in tension only. A hook also needs to be inside the confined core of a column or a joint to work.

What does the calculator leave out?

The calculator leaves out headed bars, the hooks of stirrups and ties, the excess reinforcement reduction, the seismic provisions for special moment frames, which are more demanding, and the check of concrete breakout. Use the detail of the code for the case and the minimum bend diameters of the code.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.