Skip to content
Omnikalc

Reinforced concrete beam flexural capacity calculator: moment strength and ductility of a rectangular beam

Enter the beam width, the effective depth, the steel area and the material strengths to get the stress block depth, the net tensile strain, the strength reduction factor and the design moment strength.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in²

Value out of range

ksi

Value out of range

ksi

Value out of range

Results

Design moment strength φMn

272.7 kip-ft

Depth of the equivalent stress block, a
4.65 in
Net tensile strain in the steel
0.0088
Tension-controlled: the beam fails in a ductile way
Strength reduction factor φ
0.90
Steel area over the minimum steel area
3.67
The steel meets the minimum area

The reinforced concrete beam flexural capacity calculator gives the design moment strength φMn of a rectangular, singly reinforced beam from its width, its effective depth, its steel area and the material strengths, with the net tensile strain and the minimum steel check of ACI 318.

How the calculation works

  • Enter the width of the beam, the effective depth from the compression face to the centroid of the tension steel and the area of tension steel.
  • Enter the concrete strength f′c and the yield strength fy of the reinforcement.
  • The calculator finds the depth of the stress block a = As fy / (0.85 f′c b), the net tensile strain and the strength reduction factor φ of ACI 318.
  • It gives the design moment φMn = φ As fy (d − a/2) and checks the minimum steel.

Example

A beam 12 in wide with an effective depth of 21.5 in has 3.16 in² of steel (four No. 8 bars), with f′c = 4 ksi and fy = 60 ksi. The stress block is a = 3.16 × 60 / (0.85 × 4 × 12) = 4.65 in, and c = a / 0.85 = 5.47 in. The net tensile strain is 0.003 × (21.5 − 5.47) / 5.47 = 0.0088, above 0.005, so the beam is tension-controlled with φ = 0.90. The nominal moment is 3.16 × 60 × (21.5 − 2.32) / 12 = 303.0 kip-ft, and the design moment is 272.7 kip-ft.

Why it matters

The calculator helps structural engineers, builders and students to check a beam, to see the effect of the steel area and of the depth on the capacity, and to know whether the beam will behave in a ductile way. It reproduces the hand calculation taught in every reinforced concrete course.

Good to know

Use the effective depth, measured to the centroid of the steel, and not the total depth: subtract the cover, the stirrup and half of the bar. Check that εt is at least 0.005 for beams, and that the steel is within the maximum and minimum. Check the shear, the deflection and the cracks as well. For a real project, the structural engineer must verify the design.

The stirrup spacing calculator covers shear reinforcement, the concrete crack width calculator covers cracks, the rebar development length calculator covers anchorage and the one-way slab minimum thickness calculator gives span-to-depth limits.

Frequently asked questions

How is the moment strength of a beam found?

For a rectangular beam with tension steel only, the compression in the concrete is replaced by an equivalent rectangular stress block of depth a = β1 c, with a stress of 0.85 f′c. The equilibrium of forces gives a = As fy / (0.85 f′c b), and the nominal moment is Mn = As fy (d − a/2). The design moment φMn is the nominal moment multiplied by the strength reduction factor.

What is the net tensile strain?

The net tensile strain εt is the strain in the extreme tension steel at the nominal strength, with the concrete at the crushing strain of 0.003. If εt is 0.005 or more, the section is tension-controlled, the steel yields well before the concrete crushes, and the beam gives a visible warning with large deflections and cracks. ACI 318 gives φ = 0.90 for such a section, and decreasing values down to 0.65 when εt falls to 0.002.

What is the minimum steel?

A beam must have a minimum amount of steel so that the moment that cracks the concrete does not exceed the strength of the steel, which would cause a sudden failure without warning. ACI 318 requires As,min = the larger of 3√f′c / fy and 200 / fy (in psi), times b d. The ratio shown is the steel area divided by this minimum, and it should be at least 1.

What are the limits of the calculator?

It is for a singly reinforced rectangular section, with no compression steel and no flange. T-beams, doubly reinforced beams, beams with several layers of steel and beams with axial loads need other calculations. The design must also check the shear, the deflection, the crack control, the development of the bars and the detailing, and a licensed engineer must verify a real structure.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.