Skip to content
Omnikalc

Shear friction calculator: design strength and required steel across a concrete shear plane

Enter the steel area, the concrete area, the material strengths, the condition of the shear plane and the factored shear to get the shear friction strength, its limit, the design strength, the ratio and the steel required.

Updated on
Your inputs
in²

Value out of range

in²

Value out of range

ksi

Value out of range

psi

Value out of range

kips

Value out of range

Results

Demand to capacity ratio

0.93

Design strength is enough for the factored shear
Nominal shear friction strength
100.8 kips
Upper limit of the strength
230.4 kips
Design shear strength (φVn)
75.6 kips
Reinforcement required
1.11 in²

The shear friction calculator gives the nominal strength, its upper limit, the design strength, the demand to capacity ratio and the reinforcement required to transfer a shear force across a concrete plane, by the ACI 318 shear friction method, from the steel, the concrete and the condition of the interface.

How the calculation works

  • Enter the area of the reinforcement that crosses the shear plane, the area of concrete that resists the shear, the steel yield strength and the concrete strength.
  • Choose the condition of the shear plane, which gives the friction coefficient μ, and enter the factored shear force on the plane.
  • The calculator finds the nominal strength μ Avf fy, its upper limit, the design strength with φ = 0.75, the demand to capacity ratio and the reinforcement required.

Example

A corbel has 1.2 in² of reinforcement across a monolithic shear plane (μ = 1.4) of 288 in², with fy = 60 ksi and f’c = 4000 psi. The factored shear is 70 kips. The nominal strength is 1.4 × 1.2 × 60 = 100.8 kips, below the limit of 230.4 kips. The design strength is 0.75 × 100.8 = 75.6 kips, so the ratio is 70 / 75.6 = 0.93. The reinforcement required is 70 / (0.75 × 1.4 × 60) = 1.11 in².

Why it matters

The calculator helps structural engineers, precast designers, detailers and students to check corbels, brackets, wall to footing joints, precast connections and construction joints in a first design, and to see how the surface preparation changes the steel needed.

Good to know

Anchor the bars on both sides of the plane so that they can reach their yield strength, and roughen the interface when the design assumes it. Check the flexure and the direct tension of the member, and add the steel for them to the shear friction steel when the code asks for it.

The punching shear calculator checks slab columns, the rebar development length calculator gives the anchorage, the concrete crack width calculator checks the service crack and the RC beam flexural capacity calculator gives the bending strength.

Frequently asked questions

What is shear friction?

Shear friction is a design model of ACI 318 for the transfer of shear across a plane, such as a crack, a cold joint, the interface between a precast member and a cast in place concrete, or the connection of a corbel to a column. The shear makes the two sides slip a little, the roughness of the plane makes them separate, and the reinforcement across the plane is stretched and clamps the faces together, which creates a friction force.

How is the strength calculated?

The nominal strength is Vn = μ Avf fy, where μ is the friction coefficient of the plane, Avf the area of reinforcement across it and fy the yield strength, limited to 60 ksi. The strength is limited to the smallest of 0.2 f'c Ac, (480 + 0.08 f'c) Ac and 1600 Ac in US units, where Ac is the area of the concrete resisting the shear. The design strength is φ Vn with φ = 0.75 for shear.

What value of the friction coefficient should be used?

ACI 318 gives μ = 1.4 for monolithic concrete, 1.0 for hardened concrete roughened to a full amplitude of about 1/4 in, 0.6 for hardened concrete that is not roughened, and 0.7 for concrete against structural steel with studs or reinforcement. The coefficient applies to normal weight concrete. For lightweight concrete, the values are multiplied by a factor λ and the strength limits are reduced.

What are the limits of the calculator?

The calculator uses the basic equation only. It does not include the effect of a permanent compression across the plane, which can be added to the clamping force, the tension across the plane which needs additional steel, the anchorage of the bars, the flexure and the direct tension of a corbel, or the lightweight concrete. The structural design must be done by a licensed engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.