Skip to content
Omnikalc

Steel fatigue detail category and life calculator

Choose a detail category, enter the stress range, the cycles per day and the design life to get the cycles to failure, the damage ratio, the fatigue life in years and the allowable stress range.

Updated on
Your inputs
ksi

Value out of range

Value out of range

years

Value out of range

Results

Fatigue damage ratio

0.67

The detail has enough fatigue life
Threshold stress range used
5.0 ksi
Cycles in the design life
13.7 million
Cycles to failure at this stress range
20.4 million
Fatigue life
112 years
Allowable stress range for the design life
6.9 ksi

The steel fatigue life calculator uses the detail category and the stress range of a steel connection to give the cycles to failure, the damage ratio, the fatigue life and the allowable stress range with the S-N relation of AISC and AASHTO.

How the calculation works

  • Choose the detail category (A to E’) of the connection and enter the stress range at the detail.
  • Enter the stress cycles per day, the design life and the type of amplitude.
  • The calculator gives the cycles to failure, the damage ratio, the fatigue life in years and the allowable stress range.

Example

A category C detail has a constant A = 44 × 10⁸ ksi³ and a threshold of 10 ksi. It sees a stress range of 6 ksi, 500 cycles per day for 75 years, so 13.69 million cycles. For variable amplitude the limit is half of the threshold, 5.0 ksi, so the stress range counts. The cycles to failure are 44 × 10⁸ / 6³ = 20.37 million, and the damage ratio is 13.69 / 20.37 = 0.67. The fatigue life is 112 years, and the allowable stress range for the design life is 6.85 ksi.

Why it matters

The calculator helps bridge and crane engineers, inspectors and students to check a welded or bolted detail under repeated live load, to compare categories and to find the stress range that gives the life they need.

Good to know

Take the stress range at the detail, from the live load only, with the section properties at the detail and the effect of the impact. Pick the category from the code tables for the exact geometry, since the same weld can be category C or E, depending on the length of an attachment. Count the cycles as the number of stress ranges, not the number of trucks, because a truck can give several cycles in a long span. A ratio above one means that the life is shorter than the design life, and the detail should be changed, not just the stress, so the category improves.

The Basquin fatigue life calculator gives cycles for a stress amplitude, the Goodman calculator gives the safety factor with a mean stress, the endurance limit calculator gives the fatigue strength of a part and the Paris law calculator gives the growth of a crack.

Frequently asked questions

What is a detail category?

For fatigue, a steel detail is classed by how badly it concentrates stress. A plain rolled plate is category A, and a weld at the end of a cover plate is E or E'. The category sets a constant A for the S-N line, N = A / S³, and a constant amplitude fatigue threshold, below which the detail has an infinite life under a constant stress range. A lower category fails sooner at the same stress range.

Why use the stress range?

Fatigue in welded steel depends on the range of the stress, not on the mean stress, because the residual stress of the weld is near yield. So the calculator uses the difference between the maximum and the minimum stress at the detail from the live load, and not the maximum stress. The constants are for a number of cycles of that range.

What is the difference between constant and variable amplitude?

Under a constant stress range, the cycles below the threshold do no damage. Under the variable stress ranges of traffic, the small cycles can add up once the large ones have started a crack, so the S-N line is extended down to half of the threshold for the design. The calculator offers both choices.

What does the calculator leave out?

The calculator leaves out the equivalent stress range of a spectrum by Miner's rule, the effect of the thickness, the corrosion, the weld quality, the retrofit and the inspection. Use the code tables of AISC 360 appendix 3 or AASHTO to pick the category and an inspection plan for the real structure.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.