Skip to content
Omnikalc

Endurance limit calculator: how much cyclic stress can your part take forever?

Enter the tensile strength, the surface, the size, the loading, the temperature and the reliability to get the corrected endurance limit with the Marin factors.

Updated on
Your inputs
ksi

Value out of range

in

Value out of range

°F

Value out of range

Results

Corrected endurance limit Se

24.2 ksi

Test-specimen endurance limit S'e (0.5 × Sut)
40.0 ksi
Surface factor ka
0.845
Size factor kb
0.879
Product of all the Marin factors
0.605

A shaft or a spring can fail under a stress well below its yield strength if the stress repeats millions of times, and the fatigue strength is lower than the lab data suggests. The endurance limit calculator takes the tensile strength, the surface finish, the diameter, the type of loading, the temperature and the reliability, and gives the corrected endurance limit, the test-specimen limit, the surface and size factors and the product of the Marin factors.

How the calculation works

  • Enter the ultimate tensile strength of the steel and choose the surface finish, the type of loading and the reliability you need.
  • Enter the diameter of the part and its operating temperature.
  • The calculator starts from the endurance limit of a polished test specimen, S’e = 0.5 × Sut, up to a cap of 100 ksi.
  • It multiplies by the Marin factors: ka for the surface, kb for the size, kc for the loading, kd for the temperature and ke for the reliability, to give Se = ka × kb × kc × kd × ke × S’e.

Example

A machined steel shaft has Sut = 80 ksi, a diameter of 1 in, bending load, a temperature of 70 °F and a required reliability of 99 %. The test limit is S’e = 40 ksi. The surface factor is 2.70 × 80^−0.265 = 0.845, the size factor is 0.879 × 1^−0.107 = 0.879, the load and temperature factors are 1.00, and the reliability factor is 0.814. The product is 0.605, so the endurance limit of the shaft is 24.2 ksi.

Why it matters

The corrected endurance limit is the first input of any fatigue calculation, whether it is a Goodman diagram, a Soderberg line or a stress-life check of a shaft. It shows how much a good surface finish or a smaller diameter helps, and how much the strength falls as the reliability rises.

Good to know

The calculator follows the Shigley method for steel with a tensile strength up to 200 ksi (1,400 MPa), within the size ranges of the equations. It leaves out stress concentration, which is applied to the stress, and the effects of residual stress, corrosion, coatings and fretting. Real design needs a margin, test data and review by an engineer. Treat the result as a first estimate.

The Brinell hardness calculator relates hardness to tensile strength, the principal stress calculator finds the main stresses at a point, the shaft torsion calculator checks twisted shafts, and Young’s modulus calculator covers stiffness.

Frequently asked questions

What is the endurance limit?

It is the highest alternating stress that a steel part can take for an unlimited number of cycles without fatigue failure. Many steels show such a limit at about half of their tensile strength in a polished lab test. Below it, the S-N curve flattens, and above it, the part fails after a finite number of cycles.

Why is the real limit lower than the test value?

A lab specimen is small, polished, loaded in bending, at room temperature, and its result is a 50 % value. A real part is larger, rougher, loaded differently, hotter or colder and must be more reliable than a coin flip. Each difference reduces the strength, and the Marin factors, one for each, correct the test value.

What do the factors mean?

The surface factor ka drops with rougher finishes and with higher strength steels, because notches from machining and scale matter more. The size factor kb drops with diameter since a larger part has a larger stressed volume. The load factor kc is 1 for bending, 0.85 for axial load and 0.59 for torsion. The reliability factor ke is 0.814 for 99 %.

Does this apply to aluminium and to high-strength steels?

Not directly. Aluminium has no true endurance limit, and the formula here stops at a tensile strength of 200 ksi, since above it the ratio of the limit to the strength falls. Stress concentrations, residual stress, corrosion and shot peening are also not in the factors. Use test data when you have it.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.