Skip to content
Omnikalc

Open web steel joist chord force and bridging calculator

Enter the roof load, the joist spacing and span, the chord distance and area, the yield strength and the bridging spacing to get the moment, the chord force, the deflection and the bridging.

Updated on
Your inputs
psf

Value out of range

ft

Value out of range

ft

Value out of range

in

Value out of range

in²

Value out of range

ksi

Value out of range

ft

Value out of range

Results

Ratio of the stress to 0.6 Fy

0.61

The chords can carry the force
Bending moment
40.0 kip-ft
Chord force
21.82 kip
Chord stress
18.18 ksi
Deflection
1.61 in
Ratio of the deflection to L/240
0.80
The deflection is within L/240
Rows of bridging
3

The open web steel joist chord force and bridging calculator gives the bending moment, the chord force, the chord stress, the deflection and the rows of bridging of a simply supported open web steel joist, from the load, the span, the depth of the chords and the area of a chord.

How the calculation works

  • Enter the roof load, the spacing and the span of the joists.
  • Enter the distance between the chords, the area of a chord, the yield strength and the spacing of the bridging.
  • The calculator finds the moment, the chord force and stress, the deflection and the rows of bridging.

Example

Joists at 5 ft under 40 psf carry 200 plf. On a span of 40 ft, the moment is 200 × 40² / 8 = 40.0 kip-ft. With 22 in between the chords, the chord force is 40 × 12 / 22 = 21.82 kip, and with 1.2 in² the stress is 18.18 ksi, a ratio of 0.61 to 0.6 × 50. The deflection is 1.61 in, a ratio of 0.80 to L/240. Bridging every 10 ft needs 3 rows.

Why it matters

The calculator helps steel detailers, building designers, contractors and students to see how a joist works, to estimate the force in its chords and its deflection, to count the rows of bridging, and to compare the effect of the span and of the depth.

Good to know

Select the joists from the load tables of the manufacturer, and check the uplift of the wind, which puts the bottom chord in compression, with an extra bridging. Install the bridging before the construction loads are applied, and anchor the ends of the joists as shown. Do not hang loads from the joists between the panel points.

The roof truss calculator plans the trusses of a roof, the cold-formed purlin span check calculator checks a purlin, the diaphragm shear and chord force calculator checks a diaphragm and the beam deflection calculator gives the deflection of a beam.

Frequently asked questions

What is an open web steel joist?

An open web steel joist is a light truss, made of top and bottom chords of angles and of web members of round bars or angles, that carries a floor or a roof between the beams or the walls. It is light and economical for medium and long spans, and the services can go through its openings. The joists are made to standard series, and the loads are chosen from the load tables of the manufacturer.

How is the force in the chords found?

The bending moment of the joist is carried by the two chords as a couple of forces. The force in each chord is the moment divided by the distance between the centroids of the chords, compressive in the top chord and tensile in the bottom chord. The stress is the force divided by the area of the chord, and it is compared with an allowable stress of 0.6 Fy for the allowable stress design.

What are the rows of bridging for?

The bridging connects the joists to each other to brace the top chord against the buckling to the side, and to keep the joists in line during the erection. The maximum spacing of the rows depends on the span and on the section of the joist, and it is given in the standards of the Steel Joist Institute. The calculator counts the rows from a maximum spacing that you enter.

What are the limits of the calculator?

The calculator is a simple approximation of the chords of a joist. It does not check the buckling of the top chord between the panel points, the web members, the connections, the end bearing, the effect of the uplift of the wind or the real stiffness of the joist. Joists must be selected from the load tables of the manufacturer, and the bridging must be placed as the standard says.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.