Skip to content
Omnikalc

Subsurface drain calculator: capacity of a perforated pipe for a drained area

Enter the area drained, the drainage coefficient, the pipe diameter, the slope and the roughness to get the inflow, the full-flow capacity, the velocity and the ratio.

Updated on
Your inputs
ft²

Value out of range

%

Value out of range

Results

Full-flow capacity of the pipe

65.4 gpm

Design inflow to the drain
18.9 gpm
Velocity at full flow
1.67 ft/s
Ratio of the inflow to the capacity
0.29
The pipe has enough capacity

The subsurface drain calculator gives the design inflow, the full-flow capacity, the velocity and the ratio of the inflow to the capacity of a perforated drain pipe, from the area drained, the drainage coefficient, the diameter, the slope and the roughness of the pipe.

How the calculation works

  • Enter the area drained and choose the drainage coefficient, which is the depth of water to remove per day.
  • Choose the diameter of the drain pipe, enter its slope and choose its Manning roughness.
  • The calculator finds the design inflow, the full-flow capacity of the pipe, the velocity and the ratio of the inflow to the capacity.

Example

An area of 43,560 ft² (1 acre) drained at 1.0 in/day gives an inflow of 43,560 × 1 / 12 × 7.48 / 1,440 = 18.9 gpm. A pipe of 4 in at a slope of 0.5 % with n = 0.012 has a velocity of 1.486 / 0.012 × (4/48)^(2/3) × 0.005^0.5 = 1.67 ft/s and a full-flow capacity of 65.4 gpm. The ratio of the inflow to the capacity is 0.29.

Why it matters

The calculator helps site and drainage designers, landscape and foundation contractors, farmers and students to size an underdrain, to check that the pipe is not too small for the area and to compare the effect of the slope and of the diameter.

Good to know

Install the pipe with the holes down or according to the pipe maker, in a trench with clean gravel and a filter fabric, and keep a constant slope to a free outlet. Use cleanouts at the changes of direction, protect the outlet from the small animals and the sediment, and keep the drain away from the roots of the trees. Size the pipe with a margin, because a larger pipe costs little more than a pipe that clogs.

The Manning equation calculator gives the flow of an open channel or a pipe, the pipe flow velocity calculator relates the flow and the pipe size, the Darcy’s law calculator gives the flow in the soil and the permeable pavement reservoir depth calculator sizes a stone reservoir.

Frequently asked questions

What is a subsurface drain?

A subsurface drain, or underdrain, is a perforated pipe buried in a trench filled with gravel or stone and wrapped with a filter fabric, which collects the groundwater and the infiltrated water and carries it away. It is used around the foundations, under the athletic fields, behind the retaining walls and in the agricultural land to lower the water table and to keep the soil stable.

What is the drainage coefficient?

The drainage coefficient is the depth of water that the system must remove from the drained area in one day. It depends on the climate, the soil, the use of the land and the level of the protection. A value of 0.5 in/day (12 mm/day) is common for turf and light soils, 1 in/day (25 mm/day) for the foundations and the sports fields, and more for the sites with a high water table.

How is the capacity of the pipe found?

The capacity at full flow is found with the Manning equation, from the diameter, the slope and the roughness of the pipe. The design flow is usually limited to about 75 % of the capacity, to leave a margin for the sediment, the roots and the uncertainty of the inflow. A steeper slope or a larger diameter increases the capacity, and the minimum slope is about 0.2 to 0.5 % to keep the pipe clean.

What are the limits of the calculator?

The calculator uses a uniform inflow for the whole area, and the full-flow capacity of the pipe. It does not include the capacity of the perforations, the clogging of the filter, the inflow from the high ground, the spacing of the laterals, the depth of the drain or the outlet that can be submerged. The design of a large system should use the soil data and the methods of the agricultural or the geotechnical manuals.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.