Skip to content
Omnikalc

Warren truss member forces calculator

Enter the number of panels, the panel length, the height and the joint load to get the reactions, the chord forces at the middle and the diagonal forces of a simply supported Warren truss.

Updated on
Your inputs

Value out of range

ft

Value out of range

ft

Value out of range

kips

Value out of range

Results

Top chord force at the middle (compression)

67.5 kips

Bottom chord force at the middle (tension)

63.8 kips

Span of the truss
60.0 ft
Support reaction
30.0 kips
End diagonal force (compression)
35.4 kips
Diagonal force in the middle panel
7.1 kips
Length of a diagonal
9.4 ft

The Warren truss calculator gives the reactions, the top and bottom chord forces at the middle and the diagonal forces of a simply supported Warren truss under equal vertical joint loads, from the method of joints and sections.

How the calculation works

  • Enter the number of panels (an even number), the panel length, the height and the load at each interior joint of the bottom chord.
  • The calculator finds the reactions by symmetry and cuts the truss with the method of sections at the middle.
  • It gives the chord forces at the middle, the end diagonal, the diagonal in the middle panel and the length of a diagonal.

Example

A Warren truss has 6 panels of 10 ft and a height of 8 ft, with 12 kips at each of the 5 interior joints of the bottom chord. The span is 60 ft and each reaction is 5 × 12 / 2 = 30 kips. The diagonal is √(8² + 5²) = 9.43 ft. The top chord at the middle takes 12 × 10 × 36 / (8 × 8) = 67.5 kips in compression and the bottom chord 63.8 kips in tension. The end diagonal takes 30 × 9.43 / 8 = 35.4 kips and the middle diagonal 7.1 kips.

Why it matters

The calculator helps structural engineers, builders and students to size the members of a floor or roof truss, to see how the height changes the chord forces and to check the results of a truss program.

Good to know

A taller truss has smaller chord forces, because the chords carry the moment as a couple over the height, but longer diagonals. The compression members must be checked for buckling with the unbraced length of the panel, and the tension members for the net section at the bolts. The end diagonal has the largest force and the middle diagonals the smallest. If the loads are on the top chord, or the number of panels is odd, the numbers change and a full analysis is needed. Add the self-weight of the truss to the joint loads.

The roof truss calculator gives the framing of a roof, the steel tension member calculator checks a tension member, the bolt shear capacity calculator checks the connections and the beam deflection calculator gives the deflection of the equivalent beam.

Frequently asked questions

What is a Warren truss?

A Warren truss has top and bottom chords joined only by diagonal members that alternate in direction, forming a series of triangles, without verticals. The diagonals carry the shear, in tension and compression alternately, and the chords carry the bending moment as a couple. It is used for roofs, floors and bridges because of its simple geometry.

How are the forces found?

The method of sections cuts the truss through three members and takes moments about the point where two of them meet. A chord force is the bending moment at the joint opposite to it divided by the height. A diagonal force is the shear in the panel divided by the sine of the diagonal angle. The calculator does this for the middle and the end.

Where is the load applied?

The calculator assumes equal vertical loads at the interior joints of the bottom chord, as in a floor truss hung from or resting on the bottom chord, and no load on the end joints that go straight to the supports. For a roof with loads on the top chord, the chord moment centers change slightly, so use a full analysis.

What does the calculator leave out?

The calculator leaves out the self-weight of the members, the bending in the chords from loads between the joints, the secondary moments of the stiff joints, buckling of the compression members and an odd number of panels. The forces are axial and for the pinned joint model. Design the members and the connections separately.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.