Skip to content
Omnikalc

Trench sloping and excavation volume calculator

Enter the depth, the bottom width and the length of the trench, the soil type and the swell to get the top width, the section, the volume in place and the loose spoil.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

%

Value out of range

Results

Width at the top

27.0 ft

Horizontal run of each side
12.00 ft
Cross-section area
180.0 ft²
Volume in place
666.7 yd³
Volume of loose spoil
833.3 yd³

The trench sloping calculator gives the horizontal run of the sides, the top width, the cross-section area, the volume in place and the loose spoil of a trench, from its depth, bottom width and length, the soil type and the swell.

How the calculation works

  • Enter the depth, the bottom width and the length of the trench.
  • Choose the soil type, which sets the side slope, and enter the swell of the soil.
  • The calculator finds the horizontal run, the top width, the section, the volume in place and the loose spoil.

Example

A trench 12 ft deep and 3 ft wide at the bottom in Type B soil has side slopes of 1 to 1, so each side runs 12 ft and the top is 3 + 2 × 12 = 27 ft wide. The section is (3 + 27) / 2 × 12 = 180 ft², and 100 ft of trench removes 180 × 100 / 27 = 666.7 yd³ in place, that is 833.3 yd³ of loose spoil with 25 percent of swell.

Why it matters

The calculator helps excavation contractors, site supervisors, safety officers and estimators to plan the width of the top of a trench, to estimate the volume to excavate and haul, and to see what room the sloping needs before the work starts.

Good to know

Slope the sides of the excavation at the angle of the worst soil that you find in the depth of the trench, and re-classify after rain. Keep the spoil piles at least 2 ft from the edge, provide a ladder or a ramp within 25 ft of the workers, and check the trench every day. If the room for the slope is not available, use a trench box or shoring, and recompute the width of the trench.

The excavation calculator gives the volume of an excavation, the trench dewatering calculator sizes the pumping of a trench, the pipe trench bedding and backfill calculator gives the quantities of the pipe zone and the trench pipe laying production calculator gives the length of pipe laid per day.

Frequently asked questions

What are the OSHA soil types and slopes?

Subpart P of 29 CFR 1926 classifies the soil as stable rock, Type A, Type B or Type C. The maximum allowable slope for an excavation of 20 ft or less is vertical for stable rock, 3/4 to 1 for Type A, 1 to 1 for Type B and 1 1/2 to 1 for Type C. A competent person classifies the soil by visual and manual tests, and a wet or disturbed soil is often Type C.

What is benching?

Benching is cutting the sides of the excavation in steps instead of in a single slope. For Type A and Type B soils, simple benching is allowed with the same total slope. In Type C soil, benching is not allowed, and a single slope of 1 1/2 to 1 or a protective system is used. The calculator gives the width of the top for the sloped trench, which is the same as the width of the benched trench at the top.

When is a protective system required?

Any excavation deeper than 5 ft needs a protective system, such as sloping, benching, shoring or a trench box, unless it is in stable rock. A competent person must inspect the excavation every day, and an excavation deeper than 20 ft needs a design by a registered professional engineer. Keep the spoil and the equipment at least 2 ft back from the edge.

What does the calculator leave out?

The calculator takes a trench with a constant depth and a flat bottom. It does not include the steps for a deep trench, the surcharge of a nearby building, the water in the trench, the slope of the ground, the ramps at the ends or the overbreak. The volume in place is the cut, and the loose spoil is the cut times the swell. The soil classification stays the responsibility of the competent person.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.