Skip to content
Omnikalc

Whitmore width calculator: check the tension strength of a gusset plate

Enter the bolt group size, the plate thickness and strengths, the holes and the factored tension to get the Whitmore effective width, the yielding and rupture strengths of the gusset plate and the demand-to-capacity ratio.

Updated on
Your inputs
in

Value out of range

in

Value out of range

°

Value out of range

in

Value out of range

ksi

Value out of range

ksi

Value out of range

Value out of range

in

Value out of range

kips

Value out of range

Results

Demand-to-capacity ratio

34.3 %

The gusset plate is adequate
Whitmore width at the end of the bolt group
14.39 in
Yielding strength on the Whitmore section, φ = 0.90
233.2 kips
Rupture strength on the net Whitmore section, φ = 0.75
275.0 kips
Governing design strength
233.2 kips

The Whitmore section gives the effective width of a gusset plate that carries a member force. The Whitmore width calculator finds that width from the size of the bolt group and the 30-degree spread, then checks the yielding and the rupture strength of the plate against the factored tension.

How the calculation works

  • Enter the length of the bolt group along the direction of the load and its width, the distance between the outer lines of bolts, as given by the connection detail.
  • Keep the Whitmore angle at 30°, the usual value of the method, then enter the plate thickness, its yield and tensile strengths, the number of holes crossed by the width, their diameter and the factored tension.
  • The calculator finds the Whitmore width Lw = width + 2 × length × tan 30°, the effective width over which the load spreads in the plate at the end of the bolt group.
  • It computes the yielding strength φ Fy t Lw (φ = 0.90) and the rupture strength φ Fu t (Lw − n d) (φ = 0.75) of the plate, takes the smaller, and compares it with the load.

Example

A gusset plate has a bolt group 9 in long and 4 in wide, with a 30° spread, a plate 0.5 in thick of A36 steel (Fy = 36 ksi, Fu = 58 ksi), 2 holes of 0.875 in across the width and a factored tension of 80 kips. The Whitmore width is 4 + 2 × 9 × tan 30° = 14.39 in. The yielding strength is 0.90 × 36 × 0.5 × 14.39 = 233.2 kips and the rupture strength is 0.75 × 58 × 0.5 × (14.39 − 2 × 0.875) = 275.0 kips. The governing strength is 233.2 kips, so the demand-to-capacity ratio is 34.3%.

Why it matters

The calculator helps structural steel designers, detailers, fabricators and students to check the gusset plate of a brace, a truss joint or a hanger connection, to choose the thickness of the plate, and to see which limit state governs, the yielding of the gross section or the rupture of the net section.

Good to know

Use the real bolt gauge and the real number of holes crossed by the Whitmore line. Limit the width to the plate edges and check the overlap with the neighboring members. Keep the connection compact, since a larger group makes a wider Whitmore section. Complete the design with the other limit states of the standard.

The bolt shear capacity calculator checks the bolts, the bolt torque calculator covers the pretension, the steel column capacity calculator checks the compression members and the fillet weld strength calculator checks welded gussets.

Frequently asked questions

What is the Whitmore section?

The Whitmore section is an effective width of a gusset plate, defined by the engineer R. E. Whitmore in 1952. The load from the last row of bolts, or from the end of the weld, is assumed to spread in the plate at 30 degrees on each side of the bolt group. The width of the plate that this line crosses at the last row, the Whitmore width, is the width that carries the member force in tension or in compression.

How is the strength checked?

In tension, the plate is checked for yielding of the gross Whitmore section, with φ = 0.90 and the yield strength Fy, and for rupture of the net section, with φ = 0.75 and the tensile strength Fu, after subtracting the holes that the width crosses. The smaller value governs. The same Whitmore width is used for the compression check, with the buckling of an equivalent column.

What if the plate is narrower than the Whitmore width?

The width of the Whitmore section is limited to the width of the plate: where the 30-degree lines reach the edge of the plate, the width is cut off. In the same way, the width of two adjacent members that share one gusset plate may overlap, and then it is counted only once. Check the real plate dimensions, and reduce the width of the bolt group that you enter if needed.

What other checks does a gusset plate need?

The Whitmore check is only one of them. The plate also needs a check of the block shear at the bolts, the bearing and tear-out at the holes, the buckling in compression, the shear and the bending of the edges, and the strength of the bolts or welds. In a bracing connection, the gusset plate must also fit the capacity design rules of the code for seismic design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.