Skip to content
Omnikalc

Vehicle offtracking and swept path width calculator

Enter the turning radius, the wheelbases and the vehicle width to get the offtracking of a tractor-semitrailer, the radius of the rear axle and the swept path width in a turn.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Swept path width

23.29 ft

Offtracking
14.79 ft
Radius of the path of the rear axle
60.21 ft
Margin in the available width
2.71 ft
The vehicle fits in the available width

The offtracking calculator gives the offtracking of a tractor-semitrailer in a steady turn, the radius of the rear axle and the swept path width, and compares it with the width available.

How the calculation works

  • Enter the radius of the path of the front axle, the wheelbase of the tractor and the length from the kingpin to the trailer axle.
  • Enter the width of the vehicle and the width available in the turn.
  • The calculator gives the offtracking, the radius of the rear axle, the swept path width and the margin.

Example

A tractor-semitrailer turns with the front axle on a radius of 75 ft, with a tractor wheelbase of 20 ft and 40 ft from the kingpin to the trailer axle. The rear axle follows a radius of √(75² − 20² − 40²) = 60.21 ft, so the offtracking is 75 − 60.21 = 14.79 ft. With a vehicle width of 8.5 ft, the swept path is 23.29 ft wide, and a lane of 26 ft leaves a margin of 2.71 ft.

Why it matters

The calculator helps site designers, traffic engineers, civil engineers and students to check a turn at a driveway, a loading dock or a roundabout for a truck, and to see how the radius, the wheelbase and the width change the space needed.

Good to know

Use the radius of the path of the front axle, which is the radius of the outer wheel path minus half of the track width, not the radius of the curb. The wheelbases are the distances between the axles that matter, the tractor wheelbase to the drive axle center and the trailer length from the kingpin to the center of the trailer axles. Add a clearance of 2 to 3 ft beside the swept path, and use the AASHTO design vehicle for the type of road. For tight turns, a computer path simulation gives the real swept path including the front swing and the transient entry.

The turning radius calculator gives the turning circle of a car, the minimum curve radius calculator gives the radius for a speed, the parking lot layout calculator lays out stalls and the loading dock calculator gives the number of dock doors.

Frequently asked questions

What is offtracking?

When a long vehicle turns, the rear wheels follow a path inside the path of the front wheels. The difference between the two is the offtracking. It makes the vehicle sweep a wider strip of road than its own width, so a truck can climb a curb or enter the next lane if the corner is tight.

What is the formula?

For a steady turn, the AASHTO Green Book gives Off = R − √(R² − ΣL²), where R is the radius of the path of the front axle and the sum is of the squares of the wheelbases of the units of the vehicle, such as the tractor and the semitrailer. The longer the wheelbases and the tighter the turn, the larger the offtracking.

How do I use the swept path width?

The swept path width is the vehicle width plus the offtracking, and it is the width of the road that the vehicle needs in the turn. Compare it to the width of the turning roadway, a driveway or a loading dock approach, and add some clearance for the driver. A smaller radius or a longer vehicle makes the width larger.

What does the calculator leave out?

The calculator leaves out the transient path when the vehicle enters and leaves the curve, the front overhang and the swing of the front corner, the tail swing, the articulation of the trailer, the effect of the steering of the rear axle and the use of the opposing lane by the driver. For design, use the templates or the software for the design vehicle.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.