Skip to content
Omnikalc

Wood joist notch and bored hole limits calculator

Choose the depth of the joist and enter the hole and the notch to get the maximum notch, the maximum hole, the edge distance and the ratios to the limits.

Updated on
Your inputs
in

Value out of range

in

Value out of range

Results

Ratio of the hole to its limit

0.73

Hole within the limit

Ratio of the notch to its limit

0.65

Notch within the limit
Maximum notch at the end
2.31 in
Maximum notch outside the middle third
1.54 in
Maximum diameter of a hole
3.08 in
Edge distance of a centered hole
3.50 in
Edge distance sufficient

The wood joist notch and bored hole calculator gives the maximum notch at the end and outside the middle third, the maximum diameter of a hole, the edge distance and the ratio of your hole and your notch to their limits, from the depth of the joist.

How the calculation works

  • Choose the depth of the joist.
  • Enter the diameter of the hole you want to bore and the depth of the notch at the end of the joist.
  • The calculator finds the limits for a notch and for a hole, the edge distance and the ratio of your hole and of your notch to their limits.

Example

A 2x10 joist is 9.25 in deep. An end notch may be 9.25 / 4 = 2.31 in deep, a notch outside the middle third 9.25 / 6 = 1.54 in, and a hole 9.25 / 3 = 3.08 in in diameter. A hole of 2.25 in is 0.73 of its limit, and centered it leaves (9.25 − 2.25) / 2 = 3.50 in above and below, more than the 2 in required. A notch of 1.5 in at the end is 0.65 of its limit.

Why it matters

The calculator helps carpenters, plumbers, electricians, inspectors and homeowners to check a hole or a notch in a floor joist before they cut it, to avoid weakening the floor, and to know if a repair or a sister joist is needed.

Good to know

Drill the holes near the middle of the depth, in the zone near the middle of the span, and keep the notches at the ends of the joists, never in the middle third. Use a hole saw and not a chisel, because a rough cut starts a split. If a hole or a notch is too large, use a sister joist, move the pipe, or ask for the opinion of a designer. Remember that the limits apply to solid sawn lumber only.

The floor joists calculator sizes the joists of a floor, the wood beam span calculator gives the span of a wood beam, the beam deflection calculator gives the deflection under a load and the lag screw withdrawal calculator gives the pull-out capacity of a screw.

Frequently asked questions

What are the limits for a notch?

The International Residential Code limits a notch in the top or the bottom of a solid sawn joist to one sixth of the depth, and it does not allow a notch in the middle third of the span. At the ends of the joist, outside the bearing length, the notch may be up to one fourth of the depth. A notch reduces the section at the place where the shear is highest, so a deep notch can split the joist.

What are the limits for a bored hole?

A hole bored in a joist must have a diameter of at most one third of the depth, and the edges of the hole must be at least 2 in from the top and the bottom of the joist. Holes must also be at least 2 in from each other and from a notch. The best place for a hole is near the middle of the depth and toward the middle of the span, where the shear is small.

Can I notch and bore the same joist?

The code does not allow a notch and a hole in the same cross section, and it asks a distance of 2 in between a hole and a notch. If you need a hole for a pipe and a notch for a cable close to each other, move one of them or sister the joist. The calculator checks one notch and one hole, so check the distances between the cuts yourself.

Do these rules apply to engineered joists?

No. The limits apply to solid sawn lumber. I-joists, trusses and laminated veneer lumber have their own rules from the manufacturer, which allow openings of given sizes in given zones of the web, and which forbid cutting the flanges. Never cut an engineered joist without the approval of the manufacturer or of the engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.