Skip to content
Omnikalc

Air fuel ratio calculator: AFR, lambda and equivalence ratio

Enter the fuel and the air and fuel mass flows to get the air-fuel ratio, lambda, the equivalence ratio, the deviation from stoichiometric and the fuel flow at lambda 1.

Updated on
Your inputs

Value out of range

Value out of range

Results

Air-fuel ratio

12.50 :1

Lambda

0.850

Rich
Equivalence ratio
1.176
Deviation from stoichiometric
-15.0%
Fuel flow at lambda 1
40.8 lb/h

The air-fuel ratio is the mass of air an engine takes in for each unit mass of fuel. It decides power, economy, emissions and engine life. This air fuel ratio calculator takes the fuel, the air mass flow and the fuel mass flow to give the AFR, lambda, the equivalence ratio, the deviation from stoichiometric and the fuel flow at lambda 1.

How the calculation works

  • Air-fuel ratio (AFR) = air mass flow ÷ fuel mass flow, with both in the same unit. The calculator converts lb/min, g/s and kg/h to grams per second.
  • Lambda = AFR ÷ the stoichiometric AFR of the fuel. Lambda 1 is a chemically complete burn. Below 1 is rich, above 1 is lean.
  • Equivalence ratio = 1 ÷ lambda. It is the figure used in combustion research, where a value above 1 is rich.
  • Fuel flow at lambda 1 = air mass flow ÷ the stoichiometric AFR. Compare it with the actual fuel flow to see how much extra fuel the engine is receiving.

Example

An engine on gasoline takes 10 lb/min of air, which is 600 lb/h, and burns 48 lb/h of fuel. The AFR is 600 ÷ 48 = 12.50:1. Lambda is 12.5 ÷ 14.7 = 0.850 and the equivalence ratio is 1.176. The mixture is 15.0% richer than stoichiometric. At lambda 1 the same air would need 40.8 lb/h of fuel.

Why it matters

Engine tuners read the AFR from a wideband sensor, and the result is often shown as lambda. Converting between the two is needed every time the fuel changes, because the same lambda has a different AFR on gasoline and on E85. Calculating the mixture from measured flows is also a way to check a sensor or an injector sizing.

Good to know

Lambda 1 is not the best setting in every case. Power and cooling are better rich, economy is better slightly lean, and a three-way catalytic converter works well only in a narrow band around lambda 1. The stoichiometric values are rounded: pump gasoline varies with the blend and the season, so a sensor calibrated for pure gasoline can be off by a few percent on E10. Diesel engines always run lean on average, at lambda 1.2 to 4, so the diesel option here is mainly useful to compare the actual ratio with the chemical one.

The BSFC calculator measures fuel use per unit of power, the compression ratio calculator describes the engine geometry and the fuel consumption calculator converts the mileage.

Frequently asked questions

What is the ideal air-fuel ratio?

For gasoline the stoichiometric ratio is 14.7 parts of air to 1 part of fuel by mass. That is the mixture that burns all the fuel with all the oxygen. Engines at light load run close to it so that the catalytic converter works well.

What is lambda?

Lambda is the air-fuel ratio divided by the stoichiometric ratio of the fuel. It lets you compare fuels on one scale: lambda 1 is chemically correct for gasoline, diesel or ethanol, although the AFR for each is different.

What mixture gives the most power?

A gasoline engine makes its best power at about 12.5 to 13 to 1 (lambda 0.85 to 0.88), and its best economy slightly lean, at 15 to 16 to 1. At full load, tuners keep the mixture rich to cool the cylinder and protect the engine from knock.

Why does the fuel change the number?

Each fuel needs a different mass of air to burn. Ethanol already contains oxygen, so it needs less air: 9.0 kg for each kg of fuel. A tune made for gasoline will run lean on E85 unless fuel delivery is increased.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.