Skip to content
Omnikalc

BET specific surface area calculator

Enter two points of a gas adsorption isotherm and the molecular area to get the monolayer volume, the BET constant, the specific surface and the equivalent particle size.

Updated on
Your inputs

Value out of range

cm³/g

Value out of range

Value out of range

cm³/g

Value out of range

nm²

Value out of range

g

Value out of range

g/cm³

Value out of range

Results

Monolayer volume Vm

49.99 cm³/g

BET constant C

100.2

Specific surface area

217.6 m²/g

Slope of the BET plot
0.019803
Intercept of the BET plot
0.000200
Total surface area of the sample
108.8 m²
Equivalent sphere diameter
12.5 nm
BET plot valid (1 if the intercept is positive)
1

The BET surface area calculator gives the slope and intercept of the BET plot, the monolayer volume, the BET constant C, the specific surface area, the total area of a sample and the equivalent sphere diameter, from two points of a gas adsorption isotherm.

How the calculation works

  • Enter two relative pressures P/P₀ in the linear range, and the gas volumes adsorbed at each, in cm³ STP per gram.
  • Enter the cross-section area of the adsorbate molecule, 0.162 nm² for nitrogen at 77 K.
  • Enter the sample mass and the density of the solid.

Example

Points at 0.1 and 0.25 with 50.97 cm³/g and 64.72 cm³/g adsorbed give a BET line with a slope of 0.019803 and an intercept of 0.000200. The monolayer volume is 49.99 cm³/g, the constant C is 100.2, and the specific surface area is 217.6 m²/g. A sample of 0.5 g has 108.8 m², and a solid of 2.2 g/cm³ corresponds to spheres of 12.5 nm.

Why it matters

The calculator helps chemistry, materials and chemical engineering students and technicians who study catalysts, activated carbons, silicas, pigments, battery powders and other porous solids, and who want to check the arithmetic of a BET analysis or understand how a surface area is derived from an isotherm.

Good to know

Use volumes in cm³ at standard temperature and pressure per gram of degassed sample, and relative pressures in the range of about 0.05 to 0.35 where the BET plot is linear. The intercept of the line must be positive, and the constant C should be consistent with the pressure range. The sphere diameter assumes non-porous, smooth, monodisperse spheres, and it is only an equivalent size. Microporous materials can break the assumptions of the model. For a published value, follow the standard with at least five points.

The Langmuir isotherm calculator treats monolayer adsorption, the Freundlich isotherm calculator gives an empirical fit, the molar mass of a gas calculator converts volumes and masses and the molarity calculator handles solution concentrations.

Frequently asked questions

What is the BET method?

Brunauer, Emmett and Teller extended the Langmuir model to multilayer adsorption. In the range of relative pressure P/P₀ of about 0.05 to 0.35, a plot of (P/P₀) / [V(1 − P/P₀)] against P/P₀ is a straight line. Its slope and intercept give the monolayer volume Vm and the constant C, and Vm gives the specific surface area of a powder or a porous solid.

How are Vm and C found from the line?

With slope s and intercept i, the monolayer volume is Vm = 1 / (s + i) and the constant is C = 1 + s / i. A positive intercept is required. A large C, above about 50, indicates a strong interaction between the gas and the surface, and a very low or negative C means that the model does not apply.

How is the area computed from Vm?

The number of molecules in the monolayer is Vm / 22,414 cm³/mol × Avogadro’s number, and each covers the area σ of the molecule. For nitrogen at 77 K, σ is 0.162 nm², which gives about 4.35 m² per cm³ of gas at standard conditions. The area per gram follows from dividing by the sample mass.

How many points should be used?

Standards such as ISO 9277 use at least five points in the linear range and check the criteria of the fit. This calculator uses two points as an illustration, which gives the exact line through them. For a real measurement, use the full isotherm and the software of the instrument.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.