Skip to content
Omnikalc

Brake rotor temperature rise calculator

Enter the weight, the speed before and after braking, the front brake share and the rotor mass to get the kinetic energy absorbed, the temperature rise per stop and the stops before the fade limit.

Updated on
Your inputs
lb

Value out of range

mph

Value out of range

mph

Value out of range

%

Value out of range

lb

Value out of range

%

Value out of range

°F

Value out of range

Results

Energy absorbed by the front rotors

464.2 BTU

Temperature rise of each front rotor

141 °F

Rotor temperature after one stop

291 °F

Kinetic energy removed by the stop
736.7 BTU
Stops without cooling before the fade limit
6.0
Fade limit assumed
1,000 °F

The brake rotor temperature rise calculator gives the kinetic energy removed by a stop, the energy absorbed by the front rotors, the temperature rise per stop, the temperature after one stop and the number of stops without cooling before the fade limit.

How the calculation works

  • Enter the vehicle weight and the speeds before and after braking.
  • Enter the front share of the braking, the mass of one front rotor and the share of heat absorbed.
  • Enter the starting rotor temperature and read the heating and the number of stops.

Example

Braking a vehicle of 3500 lb from 70 mph to 0 mph removes 736.7 BTU of energy. The front rotors absorb 464.2 BTU, which raises each rotor by 141 °F to 291 °F from a start at 150 °F. With no cooling, the fade limit of 1,000 °F is reached after about 6.0 stops.

Why it matters

The calculator helps track-day drivers, mechanics, engineers and drivers of heavy vehicles who want to understand why brakes overheat on a mountain descent or a track session, to compare rotor sizes, and to choose how many hard stops a brake system can take.

Good to know

The rotor mass should be the mass of the cast iron disc only, without the hub. Iron has a specific heat of 0.11 BTU per pound and degree Fahrenheit, or 460 joules per kilogram and kelvin, and the calculator uses this value. The share absorbed by the rotor is below 100 percent because some heat goes to the pads, caliper and wheel. The fade limit depends on the pad and on the fluid. In real driving the rotor cools between stops, so the number of stops without cooling is a safe lower bound. A long descent should be taken in a low gear to use engine braking.

The brake pedal ratio calculator relates the foot force to the braking force, the stopping distance calculator gives the distance of a stop, the longitudinal weight transfer calculator shows the front load and the flywheel energy calculator relates energy to inertia.

Frequently asked questions

Where does the energy of a stop go?

The kinetic energy of the vehicle, one half of the mass times the speed squared, is turned into heat in the brakes by friction. Almost all of it goes into the rotors and the pads at first, and then it is slowly released to the air. The energy is proportional to the square of the speed: stopping from 70 mph needs about twice the energy of a stop from 50 mph.

Why is the front share used?

On most vehicles, the front brakes do 60 to 80 percent of the braking, because the weight is transferred to the front under braking. The front rotors therefore absorb most of the heat, and they heat up more than the rear ones. A vented rotor of larger mass heats less for the same stop.

What is brake fade?

Fade is the loss of braking effectiveness when the brakes are too hot. At temperatures above about 1,000 degrees Fahrenheit, or 540 degrees Celsius, the pad friction material outgasses and the friction falls, and the brake fluid can boil. It happens on long descents or repeated hard stops. The value used here is a conventional limit and depends on the pad.

Does the rotor cool between stops?

Yes, but this calculation assumes no cooling, which is the worst case for a quick series of stops, such as at the end of a straight on a track. In real use the rotor loses heat to the air by convection and radiation, more at higher speeds, so the actual temperature after many stops is lower than the number of stops suggests.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.