Skip to content
Omnikalc

Critical crack size calculator: how big a crack can your part tolerate before it breaks?

Enter the fracture toughness, the stress and the crack length to get the stress intensity, the safety factor and the critical crack size.

Updated on
Your inputs
ksi√in

Value out of range

ksi

Value out of range

ksi

Value out of range

Value out of range

in

Value out of range

Results

Safety factor on the stress intensity (KIC / KI)

1.48

The crack is below the critical size
Stress intensity KI at the crack
33.69 ksi√in
Critical crack length at this stress
0.176 in
Fracture stress for the crack you have
89.0 ksi
Minimum thickness for plane strain
0.278 in

A tiny crack in a tough metal is harmless, but the same crack in a brittle metal under high stress can make the part fail with no warning. The critical crack size calculator takes the fracture toughness, the yield strength, the applied stress, the geometry factor and the crack length, and gives the safety factor on the stress intensity, the stress intensity at the crack, the critical crack length, the fracture stress for your crack and the minimum thickness for plane strain.

How the calculation works

  • Enter the fracture toughness KIC and the yield strength of the material, the applied tensile stress and the geometry factor Y of the crack.
  • Enter the crack length a that you found or assume.
  • The stress intensity at the crack is KI = Y × σ × √(π a). Fast fracture is predicted when KI reaches KIC.
  • The critical crack length is ac = (1/π) × (KIC / (Y σ))², and the plane-strain thickness needed for KIC to be valid is 2.5 × (KIC / σy)².

Example

A high-strength steel has KIC = 50 ksi√in and σy = 150 ksi, and it carries 60 ksi with a 0.08 in edge crack (Y = 1.12). The stress intensity is 1.12 × 60 × √(π × 0.08) = 33.7 ksi√in, so the safety factor is 1.48. The critical crack length at this stress is (1/π) × (50 / 67.2)² = 0.176 in. The crack would cause fracture at a stress of 89.0 ksi, and a valid KIC test needs a thickness of at least 0.278 in.

Why it matters

Fracture mechanics is behind the safe life of aircraft, pressure vessels, pipelines, bridges and rails. The calculation shows how large a flaw can be before it matters, which sets the resolution of the inspection, and it shows why a higher stress shrinks the tolerable flaw quickly, with the square of the stress.

Good to know

The calculator uses linear elastic fracture mechanics with a single geometry factor, for a crack in a plate under tension and in plane strain. It does not cover plastic zones, ductile tearing, residual stress, mixed modes or environmental cracking. In tough or thin material, failure is governed by net-section yielding and not by fracture. Real assessments use codes such as BS 7910 or API 579.

The Young’s modulus calculator covers stiffness, the principal stress calculator finds the main stresses, the Euler buckling calculator checks slender columns, and the Brinell hardness calculator relates hardness to strength.

Frequently asked questions

What is fracture toughness?

It is the resistance of a material to the growth of a crack, measured by the critical stress intensity factor KIC. A tough material, such as a mild steel or a titanium alloy, can carry a large crack, while a brittle one, such as glass or a hard tool steel, fails with a tiny flaw. It is measured in ksi√in or in MPa√m.

What is the stress intensity factor?

It is a measure of the stress field at the tip of a crack, KI = Y σ √(π a). It grows with the stress and the square root of the crack length. When it reaches the toughness KIC, the crack runs without further load. It replaces the stress as the failure criterion for a cracked part.

Why does the thickness matter?

A valid KIC value needs plane strain at the crack tip, which is true in thick sections where the material cannot contract through the thickness. ASTM E399 requires a thickness of at least 2.5 (KIC/σy)². A thin plate has a higher, plane-stress toughness, and using KIC for it is conservative.

How does it connect to fatigue?

A fatigue crack grows slowly with each cycle until it reaches the critical length, and then the part fractures fast. The critical crack length from this calculator is the end point for a Paris law calculation. Inspections aim to find the crack long before it reaches that size, with a factor of safety.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.