Skip to content
Omnikalc

Dean number calculator for curved pipes

Enter the pipe diameter, the coil radius, the velocity and the fluid properties to get the Reynolds and Dean numbers and the effect of the curvature on the flow.

Updated on
Your inputs
in

Value out of range

in

Value out of range

ft/s

Value out of range

lb/ft³

Value out of range

cP

Value out of range

Results

Reynolds number

5,804

Dean number

1,185

Curvature ratio a / Rc (tube radius over bend radius)
0.0417
Critical Reynolds number of the curved pipe (Ito)
7,234
Flow regime (0 laminar, 1 turbulent)
0
Friction factor ratio curved / straight in laminar flow (White)
3.90

The Dean number calculator gives the Reynolds number, the curvature ratio, the Dean number, the critical Reynolds number of the curved pipe, the flow regime and the laminar friction ratio for a bend or a helical coil.

How the calculation works

  • Enter the inner diameter of the pipe and the radius of curvature of its axis.
  • Enter the mean velocity of the fluid.
  • Enter the density and the dynamic viscosity of the fluid, in centipoise.

Example

A pipe of 0.5 in coiled on a radius of 6 in, with water at 1.5 ft/s, has a Reynolds number of 5,804 and a curvature ratio of 0.0417. The Dean number is 1,185. The critical Reynolds number is 7,234, so the flow regime is 0, with laminar friction 3.90 times that of a straight pipe.

Why it matters

The calculator helps chemical, process and mechanical engineers and students who design coil heat exchangers, reactors, cooling coils, coffee machines or microfluidic channels, and need to know quickly whether the curvature will change the flow and the pressure drop.

Good to know

Use the inside diameter, the radius to the pipe axis and the average velocity in consistent units. The correlations assume a constant curvature, a smooth pipe, a single-phase Newtonian fluid and a fully developed flow. A short bend does not develop the full secondary flow, and a coil with a small pitch differs from a toroidal pipe. Use the friction ratio only in laminar flow, and use a dedicated correlation for turbulent flow or for non-Newtonian fluids.

The Reynolds number calculator characterizes the flow in a straight pipe, the friction loss calculator gives the straight-pipe losses to multiply by the ratio, the Ergun pressure drop calculator covers packed beds, and the pipe flow velocity calculator converts flow rate to velocity.

Frequently asked questions

What is the Dean number?

The Dean number compares the centrifugal and inertial forces that drive a secondary flow in a curved pipe with the viscous forces. It is De = Re × √(a / Rc), where a is the pipe radius, Rc the radius of curvature of the pipe axis and Re the Reynolds number. A larger value means a stronger pair of counter-rotating vortices over the cross-section.

Why does the curvature matter?

In a bend or coil the fluid is pushed outward by the centrifugal force, which creates a secondary flow across the section. This increases the friction, the heat transfer and the mixing, and it delays the transition to turbulence. Helical coils are used in heat exchangers and reactors for these reasons.

What is the critical Reynolds number?

In a straight pipe the flow becomes unstable at a Reynolds number of about 2,300. In a curved pipe, the secondary flow stabilizes the flow, and Ito gave Re_crit ≈ 20,000 (a / Rc)^0.32, valid for a / Rc between about 0.0003 and 0.15. The calculator shows whether the flow is above that limit.

How accurate is the friction ratio?

The ratio from White, 1 / [1 − (1 − (11.6 / De)^0.45)^(1 / 0.45)], is an empirical fit for laminar flow in coils. It is 1 for De below 11.6 and increases with the Dean number. In turbulent flow the effect is smaller and other correlations apply, so use the number only in the laminar regime.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.