Skip to content
Omnikalc

Dittus–Boelter equation calculator: forced convection of water or air inside a tube

Choose a fluid and enter the tube diameter, velocity, length and temperature difference to get the Reynolds and Nusselt numbers, the heat transfer coefficient and the heat flow.

Updated on
Your inputs
in

Value out of range

ft/s

Value out of range

ft

Value out of range

°F

Value out of range

Results

Heat transfer coefficient

1,409.3 BTU/h·ft²·°F

Nusselt number
312.2
Reynolds number
97,179
Fully turbulent: within the range of the correlation
Prandtl number
2.99
Heat transferred over the length
73,793 BTU/h
Tube length ÷ diameter
120
A long enough tube for fully developed flow

Heat transfer in a pipe depends on the flow regime and on the fluid. The Dittus–Boelter equation calculator gives the heat transfer coefficient of turbulent flow of water or air in a tube from its diameter, velocity and length, and for heating or cooling. It shows the Reynolds, Prandtl and Nusselt numbers and the heat transferred for a given temperature difference.

How the calculation works

  • Choose the fluid (water or air), whether it is heated or cooled, and enter the diameter, velocity, length and the wall-to-fluid temperature difference.
  • The calculator takes the viscosity, conductivity and Prandtl number of the fluid and finds the Reynolds number.
  • The Dittus–Boelter equation is Nu = 0.023 Re^0.8 Pr^n, with n = 0.4 for heating of the fluid and n = 0.3 for cooling.
  • The heat transfer coefficient is h = Nu k / D, and the heat is h × π D L × ΔT.

Example

Water at 140 °F (60 °C) is cooled in a 1 in tube at 6 ft/s, over 10 ft with a wall 20 °F colder. The Reynolds number is 97,179 and the Prandtl number is 2.99. The Nusselt number is 312, and the coefficient is 1,409 BTU/h·ft²·°F. The heat transferred over the tube is about 73,800 BTU/h.

Why it matters

The coefficient inside a tube is needed for the design of heat exchangers, boilers, condensers, cooling circuits and radiators. The Dittus–Boelter equation gives a quick value to size the tubes before a detailed calculation, and it shows how the coefficient grows with the velocity (as v^0.8).

Good to know

The calculator uses fixed properties of water and air at five temperatures, which do not change along the tube. The correlation applies to smooth tubes and turbulent flow with Re above 10,000, and it is not valid for laminar flow, for liquid metals, for very viscous liquids or for large temperature differences. For rough tubes, use a friction factor correlation such as Gnielinski’s.

The Nusselt number calculator covers the dimensionless coefficient, the Prandtl number calculator covers the fluid property, the Reynolds number calculator covers the flow regime, and the LMTD calculator covers the use of the coefficient in a heat exchanger.

Frequently asked questions

What is the Dittus–Boelter equation?

It is the correlation Nu = 0.023 Re^0.8 Pr^n for forced convection in smooth tubes in turbulent flow, with n = 0.4 when the fluid is heated and n = 0.3 when it is cooled. It was published by Dittus and Boelter in 1930 and is still taught as the first correlation for the heat transfer in a pipe.

When is it valid?

For fully developed turbulent flow (Re above 10,000), Prandtl numbers from 0.6 to 160, and a tube with a length of at least 10 diameters. The temperature difference between the wall and the fluid must be moderate, because the correlation uses the properties at the mean temperature of the fluid. For large differences or viscous liquids, the Sieder–Tate correlation is used.

Why are the exponents different for heating and cooling?

The properties of the fluid near the wall differ from those at the mean temperature. A heated liquid is thinner near the wall, which lowers the viscous sublayer and raises the coefficient, and a cooled liquid acts in reverse. The exponent of 0.4 and 0.3 takes this into account in a simple way.

Is the correlation the best one available?

The more recent Gnielinski correlation is more accurate (about ±10 %) and covers transitional flow, with the friction factor. The Dittus–Boelter equation can be 25 % off in some cases. It remains popular because it is simple and good enough for a first estimate of the coefficient of a heat exchanger tube.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.