Skip to content
Omnikalc

Fin efficiency calculator: how well does a fin shed heat?

Enter the convection coefficient, the conductivity and the fin dimensions to get the fin efficiency, the heat lost and the fin effectiveness.

Updated on
Your inputs
BTU/h·ft²·°F

Value out of range

BTU/h·ft·°F

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

°F

Value out of range

Results

Fin efficiency

84.7 %

Fin parameter m
5.88 1/ft
Dimensionless length mLc
0.750
Heat lost by the fin
32.4 BTU/h
Fin effectiveness
43.2

Adding fins to a surface increases its area for heat transfer, but the fins are cooler away from the base, so they do not work at full strength. The fin efficiency calculator takes the convection coefficient, the fin conductivity, the thickness, length and width and the temperature difference, and gives the fin efficiency, the fin parameter m, the dimensionless length m·Lc, the heat lost by the fin and the fin effectiveness.

How the calculation works

  • Enter the convection coefficient between the fin and the air, the conductivity of the fin material and the thickness, length and width of a straight rectangular fin.
  • Enter the temperature difference between the base of the fin and the surrounding air.
  • The fin parameter is m = √(h P / (k A)), with P the perimeter and A the cross-section. With the corrected length Lc = L + t/2 for the tip, the efficiency is η = tanh(m Lc) / (m Lc).
  • The heat lost is η × h × (2 w Lc) × ΔT, and the effectiveness compares it with the heat the base area would lose without the fin.

Example

An aluminium fin has h = 10 BTU/h·ft²·°F, k = 118, a thickness of 0.06 in, a length of 1.5 in and a width of 3 in, with a base-to-air difference of 60 °F. The parameter is m = 5.88 per foot, and with Lc = 1.53 in, m·Lc = 0.750. The efficiency is tanh(0.750) / 0.750 = 84.7 %. The fin sheds 32.4 BTU/h, and its effectiveness is 43.2, meaning that it loses 43 times the heat of the bare base.

Why it matters

Fins are everywhere: heat sinks on chips, radiators, engine cylinders, finned tubes and cooling fins on motors. The efficiency tells you whether a longer or a thicker fin is worth the extra metal, and the effectiveness tells you whether the fin does anything at all compared with a flat surface.

Good to know

The calculator is for a straight fin of constant rectangular section, with a uniform convection coefficient and a temperature that depends only on the distance from the base. It ignores the radiation, the contact resistance at the base and the interaction between neighbouring fins, which can lower the convection coefficient. Use it for estimates, and confirm real heat sinks with data or tests.

The heat sink calculator sizes a heat sink for a given power, the heat conduction calculator covers flow through a solid, the heat loss calculator estimates losses from a building, and the heat exchanger LMTD calculator sizes exchangers.

Frequently asked questions

What is fin efficiency?

It is the ratio of the heat that a fin actually loses to the heat it would lose if the whole fin were at the temperature of its base. The temperature of a real fin drops along its length, because the heat has to flow through the material, so the outer parts transfer less heat. Efficiency runs from 0 to 100 %.

How do I raise the efficiency?

Use a material of higher conductivity, such as copper or aluminium, make the fin thicker, or make it shorter. All of these lower the parameter m·Lc, and the efficiency rises as it falls. A lower convection coefficient, as in still air compared with a fan, also raises the efficiency, but it lowers the total heat.

What is fin effectiveness?

It is the ratio of the heat lost with the fin to the heat lost by the same base area without it. A fin is worthwhile when its effectiveness is well above 1, and a value under 2 is hardly worth the cost. High effectiveness comes from a high conductivity, a large perimeter-to-area ratio and a low convection coefficient.

What is the corrected length?

A fin loses some heat through its tip. Rather than adding a separate tip term, the calculation uses a corrected length Lc = L + t/2, which adds the tip area to the side area. It is accurate to a few percent for thin fins, which is the usual case for heat sinks.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.