Skip to content
Omnikalc

Model rocket apogee calculator: how high will your rocket fly?

Enter the motor impulse, burn time, liftoff mass, propellant mass and drag loss to get the apogee, the burnout speed and the thrust-to-weight ratio.

Updated on
Your inputs
N·s

Value out of range

s

Value out of range

g

Value out of range

g

Value out of range

%

Value out of range

Results

Estimated apogee

922 ft

Good thrust-to-weight for a stable launch
Altitude at burnout
232 ft
Speed at burnout
298.0 ft/s
Average thrust
6.25 N
Thrust-to-weight ratio at liftoff
6.37

Before a launch, it helps to know roughly how high a rocket will go and whether it has enough thrust to fly straight. The model rocket apogee calculator takes the motor impulse and burn time, the liftoff and propellant masses and a drag loss share, and gives the estimated apogee, the altitude and speed at burnout, the average thrust and the thrust-to-weight ratio.

How the calculation works

  • Enter the motor’s total impulse in newton-seconds and its burn time. They are printed on the motor and listed in the motor code, such as C6.
  • Enter the liftoff mass of the rocket with the motor and the propellant mass, both in grams.
  • Enter the share of the coast altitude lost to drag. Real model rockets reach roughly 40 to 70 percent less altitude on the coast than a drag-free flight.
  • The calculator finds the exhaust speed (impulse ÷ propellant mass), the speed and altitude at burnout from the rocket equation with gravity, and then the coast, v² ÷ (2g), reduced by the drag loss.

Example

A rocket weighs 100 g at liftoff with a motor of 10 N·s that burns 12 g of propellant over 1.6 s. The average thrust is 10 ÷ 1.6 = 6.25 N, and the thrust-to-weight ratio is 6.37. At burnout, the rocket flies at 298 ft/s (90.8 m/s) at 232 ft (70.9 m). A drag-free coast would add 1,380 ft, and with a 50 percent drag loss it adds 690 ft, so the estimated apogee is about 922 ft (281 m).

Why it matters

Estimating the apogee helps pick the motor, size the recovery system and choose a safe field. A rocket that goes higher than expected can land far away or disappear, and one that lifts off too slowly can arc over and hit the ground. A quick calculation before the launch avoids both.

Good to know

The model is a simple one. It assumes a constant thrust, a vertical flight and a single drag loss share, and it ignores the delay charge, wind, rod friction and the change of drag with speed. Use an altimeter or a full simulation program for precise work. Follow the safety code of your rocketry association and the rules for your launch field.

The rocket equation calculator gives the speed change for a given mass ratio, the thrust-to-weight calculator checks the launch, the projectile calculator covers the coast of a drag-free body, and the terminal velocity calculator shows how fast an object falls through the air.

Frequently asked questions

How is the apogee estimated?

The calculator treats the burn as a steady thrust with a constant exhaust speed. It uses the rocket equation to get the speed and the height at burnout, taking gravity into account, then adds the coast height v² ÷ (2g). A drag loss share reduces the coast height to match real flights.

Where do I find the motor data?

A model rocket motor is labelled with a letter for the total impulse class, a number for the average thrust in newtons and a delay number for the time before the ejection charge. A C6-5 motor has about 10 N·s and 6 N of average thrust. The maker's data sheet lists the exact impulse, burn time and propellant mass.

What thrust-to-weight ratio is needed?

Common safety codes recommend a ratio of at least 5 to 1, so that the rocket leaves the rod fast enough for its fins to stabilise it. Below that, the rocket may drift or fly unstable. The ratio is found with the average thrust and the liftoff mass.

Why is real altitude lower?

Drag, especially on the way up at high speed, takes a lot of energy, and the thrust curve of a real motor is not flat. A heavy, thin and smooth rocket loses less than a light and wide one. Test flights with an altimeter let you tune the drag loss share for your design.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.