Skip to content
Omnikalc

Isentropic flow calculator: what are the stagnation values at your Mach number?

Enter the Mach number, the gas and the static temperature and pressure to get the stagnation temperature and pressure, the density ratio, the area ratio to the throat and the flow speed.

Updated on
Your inputs

Value out of range

°F

Value out of range

Value out of range

Results

Stagnation pressure

115.0 psi

Stagnation temperature
475.7 °F
Stagnation to static pressure ratio
7.824
Stagnation to static density ratio
4.347
Area ratio A/A* (to the throat)
1.688
Flow speed
1,524 mph
Flow regime
2.00
Supersonic

A gas that accelerates or slows without friction or heat exchange follows the isentropic relations. The isentropic flow calculator takes the Mach number, the gas and the static temperature and pressure and gives the stagnation temperature, the stagnation pressure, the pressure and density ratios, the area ratio to the throat, the flow speed and the flow regime.

How the calculation works

  • Temperature ratio T₀ ÷ T = 1 + (γ − 1) ÷ 2 × M², where γ is the ratio of specific heats and M the Mach number.
  • Pressure ratio p₀ ÷ p = (T₀ ÷ T)^(γ ÷ (γ − 1)) and density ratio ρ₀ ÷ ρ = (T₀ ÷ T)^(1 ÷ (γ − 1)).
  • Area ratio A ÷ A* = (1 ÷ M) × [(2 ÷ (γ + 1)) × (1 + (γ − 1) ÷ 2 × M²)]^((γ + 1) ÷ (2 × (γ − 1))). It compares the cross-section with the throat where the flow would be sonic.
  • Flow speed = M × √(γ × R × T), where R is the specific gas constant and T the static temperature in kelvins.

Example

Air flows at Mach 2 at a static temperature of 60 °F (288.7 K) and a static pressure of 14.7 psi. The temperature ratio is 1 + 0.2 × 4 = 1.8, so the stagnation temperature is 476 °F. The pressure ratio is 1.8^3.5 = 7.82, so the stagnation pressure is 115 psi. The area ratio is 1.688, and the flow speed is 2 × 340.6 m/s = 1 524 mph.

Why it matters

The relations are the basis of nozzle, diffuser, wind tunnel and engine inlet design. They let you find the total pressure that a probe reads, size a nozzle for a given exit Mach number, and check how much the gas compresses at a given speed.

Good to know

The model assumes a perfect gas with a constant ratio of specific heats, steady one-dimensional flow, and no shocks, friction or heat transfer. The constants given for steam and combustion gas are typical values, and real gases change with temperature. Use a real-gas table for high temperature or high pressure, and treat the flow speed as the speed in the gas.

The Mach number calculator gives the Mach number from a speed and the temperature, and the pitot tube calculator finds the speed from the pressure that the tube reads.

Frequently asked questions

What is isentropic flow?

It is the flow of a gas that is both adiabatic, with no heat exchange, and reversible, with no friction or shocks. It is a good model for the core of a nozzle, a diffuser or the flow around a wing before a shock. The entropy of the gas stays constant along a streamline.

What is stagnation temperature?

It is the temperature the gas would reach if it were brought to rest without losing energy, which is the temperature on a probe tip at the nose of an aircraft. At Mach 2 in air it is 1.8 times the static temperature in kelvins. In an adiabatic flow it stays the same along the whole flow.

Why does the area ratio matter?

In a nozzle the area changes with the Mach number in a way that depends on whether the flow is subsonic or supersonic. At the throat the flow is at Mach 1 and the area is smallest. A given area ratio has two solutions: one subsonic and one supersonic. This calculator uses the Mach number you enter.

When is the isentropic assumption wrong?

A shock wave, strong friction or heat addition breaks it. Across a normal shock, the stagnation pressure drops. The static values after the shock must be computed with the shock relations. At very high Mach numbers, the gas also becomes non-ideal as vibration and dissociation start, and a constant γ no longer holds.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.