Skip to content
Omnikalc

Ramberg–Osgood stress–strain calculator

Enter the stress, the elastic modulus, the 0.2% yield strength and the hardening exponent to get the total, elastic and plastic strain and the secant and tangent moduli.

Updated on
Your inputs
ksi

Value out of range

ksi

Value out of range

ksi

Value out of range

Value out of range

Results

Total strain

0.9166 %

Plastic strain

0.5366 %

Elastic strain
0.3800 %
Plastic share of the total strain
58.5 %
Secant modulus
4,146 ksi
Tangent modulus
557 ksi

The Ramberg–Osgood calculator gives the total strain, the elastic and plastic strain, the plastic share, the secant modulus and the tangent modulus of a metal at a given stress, from its modulus, its 0.2% yield strength and its hardening exponent.

How the calculation works

  • Enter the applied stress and the elastic modulus of the metal.
  • Enter the 0.2% offset yield strength.
  • Enter the strain-hardening exponent n from a tensile test or a handbook.

Example

At a stress of 38 ksi with a modulus of 10000 ksi, a yield strength of 35 ksi and an exponent of 12, the elastic strain is 0.3800 % and the plastic strain 0.5366 %, so the total strain is 0.9166 %, with a plastic share of 58.5 %. The secant modulus is 4,146 ksi and the tangent modulus 557 ksi.

Why it matters

The calculator helps materials and mechanical engineering students, stress analysts and designers who need the stress–strain curve of aluminum, stainless steel or titanium in a finite element model or a deflection check, and who have only the yield strength, the modulus and a hardening exponent.

Good to know

The stress and the strain are the engineering values, and the equation is a fit that is best around and above the yield strength. It describes the tensile curve up to the ultimate strength, and not necking or fracture. The exponent n varies with the alloy, the temper and the direction, and the compressive curve can differ from the tensile one. Use the values of the material standard, and use test data when the stakes are high. For large strains, the true stress–strain curve is more appropriate.

The true stress strain calculator converts engineering values to true values, the Hooke’s law calculator covers the elastic range, the principal stress calculator finds the principal stresses and the Euler buckling calculator uses the modulus for slender columns.

Frequently asked questions

What is the Ramberg–Osgood equation?

It is an empirical relation between stress and strain for metals that harden gradually without a sharp yield point, such as aluminum alloys and stainless steels. The strain is the sum of an elastic part σ/E and a plastic part that follows a power law, ε = σ/E + 0.002 (σ/σ0.2)ⁿ, where σ0.2 is the 0.2% offset yield strength and n the hardening exponent.

What does the exponent n mean?

A large n means a sharp transition from elastic to plastic behavior, close to an elastic–perfectly plastic material, while a small n gives a smooth, rounded curve. Aluminum alloys have n of about 10 to 30, mild steels much higher, and austenitic stainless steels about 5 to 10. The value is fitted from a tensile test.

Why is the 0.002 term there?

The plastic strain at the 0.2% yield strength is 0.002 by definition of the offset yield strength. At σ = σ0.2 the equation gives a plastic strain of exactly 0.2%, which anchors the curve to the yield strength that is quoted in material data sheets.

What is the tangent modulus used for?

The tangent modulus is the slope of the stress–strain curve at a given stress. It governs the buckling of columns stressed beyond the elastic range, in the tangent-modulus theory, and the stiffness for incremental plastic analyses. The calculator derives it from the derivative of the equation.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.