Skip to content
Omnikalc

Sherwood number calculator: how fast does a species leave a surface in a flow?

Choose a species and fluid, then enter the flow speed, the surface length and the concentration difference to get the Sherwood number, the mass transfer coefficient and the flux.

Updated on
Your inputs
ft/s

Value out of range

ft

Value out of range

g/m³

Value out of range

Results

Mass transfer coefficient

73.4 ft/h

Mass flux from the surface
0.0527 lb/h·ft²
Sherwood number (average)
75.8
Reynolds number
17,752
Laminar boundary layer: Sh = 0.664 Re^½ Sc^⅓
Schmidt number
0.63

The Sherwood number calculator estimates how fast a substance moves from a surface into a flowing fluid. Choose a species and the fluid, then enter the flow speed, the length of the surface and the concentration difference. It gives the Sherwood number, the mass transfer coefficient, the mass flux, and the Reynolds and Schmidt numbers.

How the calculation works

  • Choose the species and fluid, and enter the flow speed, the length of the surface and the concentration difference between the surface and the stream.
  • The calculator finds the Reynolds number and the Schmidt number Sc = ν / D from stored values of viscosity and diffusion coefficient.
  • For a laminar boundary layer on a flat plate, the average Sherwood number is Sh = 0.664 Re^½ Sc^⅓, and for a mixed layer it is (0.037 Re^0.8 − 871) Sc^⅓.
  • The mass transfer coefficient is k = Sh × D / L, and the mass flux is k × Δc.

Example

Air flows at 3 ft/s along a wet surface 1 ft long, with a vapor concentration difference of 11.5 g/m³ (about half of saturation at 77 °F). The Reynolds number is 17,752 and the Schmidt number is 0.63. The Sherwood number is 75.8, and the mass transfer coefficient is 73.4 ft/h (6.2 mm/s). The evaporation flux is 0.053 lb/h·ft².

Why it matters

Mass transfer by convection controls the drying of materials, the evaporation of water, the release of vapors from a spill, the dissolving of oxygen in water, and the rate of reactors with a solid catalyst. The Sherwood number turns the flow conditions and the diffusion coefficient into a coefficient that can be used directly in a design.

Good to know

The correlations are for a flat plate with a constant concentration at the surface, in a steady flow, at low mass transfer rates, in a laminar boundary layer or a mixed layer after a Reynolds number of 500,000. Other geometries (spheres, cylinders, pipes) have other correlations. The viscosity and diffusion coefficients are stored typical values near 77 °F (25 °C), and they change with temperature and with the concentration.

The diffusion coefficient calculator gives D, the Reynolds number calculator covers the flow, the pool evaporation calculator applies the idea to water, and the Nusselt number calculator covers the heat transfer analogy.

Frequently asked questions

What is the Sherwood number?

It is Sh = k L / D, the dimensionless mass transfer coefficient, where k is the mass transfer coefficient, L a length and D the diffusion coefficient. It is the mass transfer version of the Nusselt number, and it tells how much faster the transport is than pure diffusion across the length L.

What is the Schmidt number?

It is Sc = ν / D, the ratio of the diffusion of momentum (kinematic viscosity) to the diffusion of mass. It is about 0.6 to 2 for vapors in air and 100 to 1000 or more for dissolved substances in water. It is the mass transfer version of the Prandtl number.

Why do heat and mass transfer correlations look alike?

The same boundary layer analysis applies, so the formulas have the same form with Nu replaced by Sh and Pr by Sc. This heat and mass transfer analogy (Chilton–Colburn) lets a designer use a heat transfer correlation to estimate mass transfer, which is how evaporation from a wet surface is often calculated.

Where is the coefficient used?

In evaporation of water from a pool or a wet surface, drying, dissolving and leaching of solids, absorption of gases into liquids, sublimation, humidification, oxygen transfer in water and pollutant release from surfaces. The mass flux is the coefficient times the concentration difference.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.