Skip to content
Omnikalc

Stirling engine calculator: efficiency, work per cycle and the role of the regenerator

Enter the hot and cold temperatures, the gas, the compression ratio, the regenerator effectiveness and the speed to get the work per cycle, the heat flows, the efficiency and the ideal power.

Updated on
Your inputs
°C

Value out of range

°C

Value out of range

mol

Value out of range

Value out of range

%

Value out of range

rpm

Value out of range

Results

Thermal efficiency of the ideal cycle

60.6%

Net work per cycle

111.4 J

Carnot efficiency between the same temperatures
66.1%
Heat taken from the hot source per cycle
183.9 J
Heat rejected to the cold source per cycle
72.4 J
Ideal power at this speed
1,114

A Stirling engine is a heat engine in which a fixed amount of gas is sealed in a closed circuit and moved between a hot side and a cold side. Its ideal cycle has four steps: an isothermal compression at the cold temperature, a heating at constant volume, an isothermal expansion at the hot temperature and a cooling at constant volume. A regenerator stores heat during the cooling and returns it during the heating. This calculator gives the work per cycle, the heat flows, the efficiency compared with Carnot and the ideal power.

How the calculation works

  • Net work per cycle = n × R × (T_hot − T_cold) × ln(compression ratio)
  • Heat in = n × R × T_hot × ln(compression ratio) + (1 − ε) × n × C_v × (T_hot − T_cold)
  • Heat rejected = heat in − net work
  • Efficiency = net work ÷ heat in
  • Carnot efficiency = 1 − T_cold ÷ T_hot, with absolute temperatures
  • Ideal power = work per cycle × speed ÷ 60

Here ε is the regenerator effectiveness, n the amount of gas in moles, R = 8.314 J/(mol·K) and C_v the molar heat capacity at constant volume.

Example

0.02 mol of helium works between 650 °C and 40 °C with a compression ratio of 3 and a 90 % regenerator. The net work is 111.4 J per cycle. The engine takes 183.9 J from the hot side and rejects 72.4 J. The efficiency is 60.6 %, close to the Carnot limit of 66.1 %. At 600 rpm, the ideal power is 1,114 W.

Why it matters

With a perfect regenerator, the ideal Stirling cycle reaches the Carnot efficiency, which is the maximum allowed between two temperatures. It also runs on any external heat source, such as solar, waste heat or biomass. The comparison shows how much a poor regenerator costs.

Good to know

Real engines reach only a fraction of the ideal power, because of finite heat transfer, dead volume, friction, pumping losses and a cycle that is not made of perfect steps. The model assumes a perfect gas and an ideal regenerator at the stated effectiveness. Do not use the result to size a real engine without tests.

In practice

Increase the temperature difference or the compression ratio to see the work grow. Lower the regenerator effectiveness to see the efficiency drop away from the Carnot limit. Hydrogen and helium are preferred in real engines because of their low molar mass. This tool is for education.

Frequently asked questions

Why is the Stirling cycle efficiency equal to Carnot?

With a perfect regenerator, all the heat exchanged during the constant volume steps stays inside the engine. Only the isothermal steps exchange heat with the outside, at the two extreme temperatures, which is exactly the Carnot condition.

What does the regenerator do?

It is a porous matrix that absorbs heat from the gas when it flows toward the cold side and returns it on the way back. Without it, that heat would have to come from the hot source and be lost to the cold one.

Why are real engines less efficient?

Heat exchangers need a temperature difference to transfer heat, the regenerator is imperfect, the gas has dead volume, and friction and leaks consume power. A real engine often reaches half of the Carnot value or less.

Which gas is best?

Light gases such as hydrogen and helium flow and conduct heat better, so they allow higher speeds and power. Air is safe and cheap but gives less power.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.