Skip to content
Omnikalc

Wave power calculator: how much power does a wave carry per foot of crest?

Enter the significant wave height and the energy period to get the wave power per metre or foot of crest, the annual energy and the crest length for 1 MW.

Updated on
Your inputs
ft

Value out of range

s

Value out of range

Results

Wave power per foot of crest

5.28 kW/ft

Wave power per metre of crest
17.32 kW/m
Annual energy per foot of crest (continuous)
46.2 MWh/ft/yr
Crest length needed for 1 MW
189 ft
Deep-water group speed
23.0 ft/s

Waves are moving energy, and the power they carry across each foot of crest can be computed from just their height and period. The wave power calculator takes the significant wave height and the energy period, and gives the wave power per foot and per metre of crest, the annual energy if the sea state lasted all year, the crest length needed for 1 MW and the deep-water group speed.

How the calculation works

  • Enter the significant wave height Hs, the average height of the highest third of the waves, and the energy period Te from a wave forecast or buoy.
  • The calculator uses the deep-water formula for the wave power per unit crest length: P = ρ g² Hs² Te / (64π), with seawater density of 1,025 kg/m³.
  • This is about 0.49 × Hs² × Te kW per metre, with Hs in metres and Te in seconds.
  • It also gives the annual energy if the sea state lasted all year, the crest length that a device would need to capture 1 MW, and the group speed of the waves.

Example

A sea state with Hs = 6.5 ft (1.98 m) and Te = 9 s carries 1,025 × 9.81² × 1.98² × 9 / (64π) = 17.3 kW per metre of crest, or 5.28 kW per foot. If it lasted a year, that would be 46.2 MWh per foot of crest. A line of devices 189 ft long would see 1 MW of incoming power, and the waves travel at 23.0 ft/s in deep water.

Why it matters

Wave energy is a large renewable resource, and the first step in judging a site is to compute the power that arrives. The calculation also shows why a storm is so much more powerful than a calm sea, with power growing with the square of the height, and it helps to compare buoy data from different places.

Good to know

The formula holds for deep water, where the depth is more than half of the wavelength, and for a sea of known significant height and energy period. In shallow water, the power per unit crest is lower. The annual energy figure assumes constant conditions and 8,760 hours, so it overstates the real resource. A device study needs a full scatter table and the power matrix of the device.

The wind turbine power calculator covers another renewable source, the electricity cost calculator prices energy, the PV string sizing calculator covers solar arrays, and the energy use intensity calculator rates building consumption.

Frequently asked questions

How much power do ocean waves carry?

A typical Atlantic winter sea state carries 30 to 70 kW per metre of crest, calm summer seas carry 5 to 15 kW/m and extreme storms several hundred kW/m. The power grows with the square of the wave height and in proportion to the period. This makes high latitudes with strong swells, such as Ireland, Scotland and Chile, the best sites.

What is the energy period?

It is the period of a regular wave that would have the same power as the real irregular sea, and it is a bit shorter than the peak period, about 0.9 times Tp for common spectra. If you only have the peak period, multiply it by 0.9 as a first estimate. The significant wave height Hs is the usual measure of the sea height.

Can I capture all of the wave power?

No. A real device captures only a share of the incoming power, called the capture width ratio, and it depends on how well the device matches the waves. Typical full-system efficiencies from wave to wire are 20 to 40 % at best. The calculator gives the incoming resource and not the output of a device.

Why is the annual energy only an upper bound?

The calculator assumes a sea state that lasts all year, but real seas change from hour to hour, with calm periods and storms. The annual average power is found by summing the power over a scatter table of sea states at the site. The result here is a scale for comparing one sea state with another.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.