Skip to content
Omnikalc

Weber number calculator: inertia versus surface tension

Enter the density, speed, diameter and surface tension of a drop to get the Weber number, the breakup regime and the speed at which it breaks.

Updated on
Your inputs

Value out of range

Value out of range

Value out of range

mN/m

Value out of range

Results

Weber number

2,220.8

Violent breakup: the drop shatters into a spray of fine droplets
Speed at which breakup starts (We = 12)
0.66 m/s
Dynamic pressure divided by Laplace pressure
555.2
Dynamic pressure of the flow
40,419 Pa
Laplace pressure of the drop
146 Pa

Will a falling drop stay round or burst? It depends on a tug of war between the inertia of the flow, which tears the drop apart, and surface tension, which holds it together. The Weber number is the ratio of the two, and this calculator gives it along with the speed at which breakup begins.

How the calculation works

  • Weber number We = density × speed² × diameter ÷ surface tension
  • Critical speed for breakup (We = 12) = √(12 × surface tension ÷ (density × diameter))
  • Dynamic pressure = ½ × density × speed²
  • Laplace pressure of the drop = 4 × surface tension ÷ diameter, or 2 × surface tension ÷ radius

Use the density of the liquid, the speed of the drop relative to the gas and its diameter.

Example

A water drop of 2 mm diameter hits the air at 9 m/s with a surface tension of 72.8 mN/m. The Weber number is 2,221, far above the breakup threshold. Breakup would start at only 0.66 m/s. The dynamic pressure is 40,419 Pa, compared with a Laplace pressure of 146 Pa, so the flow wins by a ratio of 555.

Why it matters

The Weber number decides the size of the droplets in sprays and mists, which matters for paint, pesticides, fuel injectors and inhalers. Too high a value gives a fine mist that drifts, and too low a value gives big drops that do not atomize. It also explains why rain drops cannot grow beyond about 6 mm in diameter: they break up as they fall.

Good to know

The threshold changes with the shape of the flow, the viscosity of the liquid and how suddenly the drop is accelerated. For viscous liquids, the Ohnesorge number is added. This calculator uses the diameter of the drop as the length and a threshold of 12 for a simple estimate. This tool is for education.

In practice

See how each variable changes the result. Halving the diameter halves the Weber number, while doubling the speed multiplies it by four, which is why the speed matters most in a spray nozzle. Replacing water with a liquid of lower surface tension, such as ethanol at about 22 mN/m, raises the Weber number more than threefold and gives finer droplets.

The Laplace pressure calculator gives the pressure inside a drop, the Reynolds number calculator compares inertia with viscosity, and the capillary rise calculator uses surface tension in a tube.

Frequently asked questions

What is the Weber number?

It is the ratio of inertia to surface tension in a flow: We = density × speed² × length ÷ surface tension. A low value means surface tension keeps the drop together, and a high value means the flow can tear it apart.

At what value does a drop break up?

A rule of thumb is a Weber number of about 12 based on the diameter, for a drop in a gas stream. Above that it flattens and bursts, and above about 50 it shatters violently. The exact threshold depends on how the speed changes.

Where is it used?

In sprays, inkjet printing, fuel injection, raindrops, spray painting, spray drying, crop sprayers and the splash of a drop on a surface. It decides the size of the droplets that a nozzle produces.

How does it differ from the Reynolds number?

The Reynolds number compares inertia with viscosity, and the Weber number compares inertia with surface tension. A flow can be dominated by one or the other, so both are used to describe a drop or a jet.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.