Skip to content
Omnikalc

Adhesive anchor epoxy volume calculator: adhesive per hole and cartridges

Enter the hole and bar diameters, the embedment depth, the number of anchors, the allowance and the cartridge size to get the adhesive per hole, the quantity to buy and the cartridges.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

Value out of range

%

Value out of range

fl oz

Value out of range

Results

Adhesive to buy with the allowance

91.8 fl oz

Adhesive per hole
0.367 fl oz
Cartridges
5
Anchors per cartridge
47.9

The adhesive anchor epoxy volume calculator gives the adhesive per hole, the quantity to buy, the number of cartridges and the anchors per cartridge for bars or rods set in concrete with an epoxy, from the hole and bar diameters and the embedment depth.

How the calculation works

  • Enter the diameter of the hole, the diameter of the bar and the embedment depth.
  • Enter the number of anchors, the allowance for the waste and the nozzle and the size of a cartridge.
  • The calculator finds the adhesive per hole, the adhesive to buy, the number of cartridges and the anchors per cartridge.

Example

A 1/2 in bar is set 6 in deep in a hole of 0.625 in. The annular space is π / 4 × (0.625² − 0.5²) × 6 = 0.663 in³, or 0.367 fl oz of adhesive per hole. For 200 anchors with a 25 % allowance, the job needs 0.367 × 200 × 1.25 = 91.8 fl oz. With cartridges of 22 fl oz, that makes 5 cartridges, and each cartridge fills about 47.9 anchors.

Why it matters

The calculator helps structural contractors, repair crews, estimators and engineers to estimate the quantity of adhesive for a number of dowels or anchors, to order the right number of cartridges, and to see how a larger hole or a deeper embedment changes the volume of adhesive.

Good to know

Drill the hole to the diameter and depth required by the manufacturer, clean it with brush and air as many times as the instructions say, and keep it dry if the product requires it. Waste the first part of the dispensed adhesive until the color is uniform. Insert the bar with a twist, wait for the cure before the loading, and check the temperature of the concrete.

The anchor bolt pullout calculator checks the capacity of a cast-in anchor, the rebar development length calculator gives the embedment of a bar, the concrete dowel bar bearing stress calculator checks a dowel at a joint and the ground anchor bond length calculator sizes a grouted anchor in the soil.

Frequently asked questions

What is an adhesive anchor?

An adhesive anchor is a threaded rod or a reinforcing bar that is set in a hole drilled in hardened concrete and bonded to it with an epoxy or another structural adhesive. It is used to connect new work to an existing structure, for example to add dowels to a slab edge, to fix a base plate, to extend a column or to connect a wall. The load is carried by the bond of the adhesive to the bar and to the concrete.

How is the volume of adhesive found?

The adhesive fills the annular space between the hole and the bar over the embedment depth. The volume is π / 4 times the difference of the squares of the hole diameter and of the bar diameter, times the depth. The volume in cubic inches is multiplied by 0.554 to get fluid ounces, and in metric the cubic millimeters are divided by 1,000 to get milliliters. The result is the adhesive in the hole when the bar is inserted.

Why add an allowance?

A part of the adhesive is lost in the mixing nozzle, in the first dispensed amount that is not well mixed and is thrown away, and in the cartridge that is not used at the end of the job. An allowance of 20 to 30 % is common. A hole that is oversized, a rough hole or a hole in a hollow block takes more adhesive, so that the allowance must be higher for them.

What are the limits of the calculator?

The calculator gives the volume of adhesive only. It does not check the load capacity of the anchor, which depends on the adhesive, the concrete strength, the edge distance, the spacing, the temperature and the cleaning of the hole, and which is given by the manual of the product and by the design rules. The product must be installed by a trained crew, with the hole cleaned as the manufacturer says.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.