Skip to content
Omnikalc

Blanking force calculator: how much press force to punch a blank

Enter the diameter of a round blank or hole, the sheet thickness and the shear strength of the material to get the cut length, the blanking force, the stripping force and the press capacity needed.

Updated on
Your inputs
in

Value out of range

in

Value out of range

ksi

Value out of range

%

Value out of range

Results

Blanking force F = L t τ

15.71 kips

Cut length (perimeter)
3.14 in
Blanking force in US tons
7.85 tons
Stripping force (about 10% of F)
1.57 kips
Required press capacity with the margin
20.42 kips
Required press capacity in US tons
10.21 tons

Blanking and punching shear a shape out of a sheet. The blanking force calculator finds the cut length, the blanking force F = L t τ, the stripping force and the press capacity needed, in kips and in US tons, for a round blank or hole.

How the calculation works

  • Enter the diameter of the round blank or hole, the thickness of the sheet and the shear strength of the material. The shear strength is about 0.8 times the tensile strength for steel.
  • Enter the safety margin for the press capacity, usually 20% to 30%.
  • The calculator computes the cut length L = π d and the blanking force F = L × t × τ, the force needed to shear the whole thickness along the cut.
  • It gives the force in kips and in US tons, the stripping force needed to pull the punch out of the sheet (about 10% of F) and the press capacity needed with the margin.

Example

A 1 in round blank is punched in a 0.125 in sheet of mild steel with a shear strength of 40 ksi. The cut length is π × 1 = 3.14 in. The blanking force is 3.14 × 0.125 × 40 = 15.71 kips, or 7.85 US tons. The stripping force is about 1.57 kips. With a 30% margin, the press must have a capacity of at least 20.42 kips, or 10.21 US tons.

Why it matters

The calculator helps tool and die makers, press operators, sheet metal shops, product designers and students to check if a press has the capacity for a punch, to size a hydraulic press for a new die, and to see the effect of the thickness and the material on the force. It prevents overloading a press.

Good to know

Use the shear strength of the actual material, from the supplier, not a table value for another grade. Add a margin of 20% to 30% to the press capacity. Do not use more than 80% of the rated capacity of a mechanical press for continuous work. Use a shear angle on the punch to reduce the force and the noise.

The hydraulic press calculator sizes the cylinder, the bend allowance calculator covers the flat length of a bent part, the Brinell hardness calculator relates hardness to strength and the Taylor tool life calculator covers the wear of cutting tools.

Frequently asked questions

How is the blanking force calculated?

In blanking and piercing, the punch shears the sheet along the cut line. The force is the area of the sheared surface times the shear strength: F = L × t × τ, where L is the length of the cut, t the thickness and τ the shear strength. The shear strength is about 0.7 to 0.8 times the ultimate tensile strength for most steels. For a rectangular or complex shape, use the total perimeter.

Can the force be reduced?

Yes. A shear angle on the punch or the die, which makes the cut progressive instead of simultaneous, can reduce the peak force by 25% to 50%, at the cost of a longer stroke. Staggering the punches in a progressive die has the same effect. A heated blank also has a lower shear strength. The energy needed per stroke does not change much.

What are the stripping force and the clearance?

After the cut, the sheet grips the punch, because the material springs back around it. The force needed to strip the sheet from the punch is about 5% to 20% of the blanking force. The clearance between the punch and the die, usually 5% to 10% of the thickness per side, affects the cut quality, the burr and the tool life, and slightly the force.

What are the limits of this calculator?

The formula gives the maximum force for a straight, clean cut in a flat sheet. It does not include the friction, the strain hardening, the speed of the press or the effect of the clearance. The press must also be able to deliver the energy over the stroke, which depends on the flywheel for a mechanical press. For a critical job, check the force with the press manufacturer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.