Skip to content
Omnikalc

Davisson pile failure criterion calculator: offset line for a pile load test

Enter the pile diameter, length, area, modulus and the load to get the elastic shortening, the Davisson offset, the settlement of the Davisson line at that load and its slope, to plot it on the load settlement curve of a test.

Updated on
Your inputs
in

Value out of range

ft

Value out of range

in²

Value out of range

ksi

Value out of range

kips

Value out of range

Results

Settlement on the Davisson line at the load

0.454 in

Elastic shortening of the pile
0.187 in
Davisson offset
0.267 in
Slope of the Davisson line (AE/L)
1,069 kips/in

The Davisson criterion calculator gives the elastic shortening of a pile, the Davisson offset, the settlement of the Davisson line at a given load and its slope, to find the failure load of a pile from a static load test.

How the calculation works

  • Enter the diameter, the length, the cross-sectional area and the modulus of elasticity of the pile.
  • Enter the load at which you want the point of the Davisson line, for example the test load or the ultimate load that you expect.
  • The calculator finds the elastic shortening PL/AE, the offset of the Davisson criterion, the settlement of the line at that load and its slope AE/L, to draw the line on the load settlement curve.

Example

A concrete pile of 14 in diameter has a length of 60 ft, an area of 154 in² and a modulus of 5000 ksi. At a load of 200 kips, the elastic shortening is 200 × 60 × 12 / (154 × 5000) = 0.187 in. The offset is 0.15 + 14 / 120 = 0.267 in. The point of the Davisson line at 200 kips is at 0.187 + 0.267 = 0.454 in of settlement, and the slope of the line is 154 × 5000 / (60 × 12) = 1,069 kips/in.

Why it matters

The calculator helps geotechnical engineers, testing laboratories, foundation contractors and students to prepare the plot of a pile load test, to check the points of the Davisson line and to compare the failure loads of different piles.

Good to know

Use the real modulus of the pile, which depends on the concrete strength for concrete piles, and the full length of the pile. Plot the line at several loads and read the intersection with the test curve. Compare it with other criteria, such as the 10 % of the diameter at the settlement.

The pile capacity calculator gives the capacity from the soil, the drilled shaft capacity calculator does the same for shafts, the pile driving formula calculator gives the capacity from the blow count and the bearing capacity calculator checks the base.

Frequently asked questions

What is the Davisson criterion?

The Davisson offset limit load is a method to find the failure load of a pile from a static load test. A line is drawn on the load settlement curve, parallel to the elastic compression line of the pile, and offset by 0.15 in plus the diameter divided by 120, for piles up to 24 in of diameter. The failure load is the load where the measured curve crosses the line. It is widely used for driven piles.

How is the line calculated?

The elastic compression line has a slope AE/L, where A is the area, E the modulus and L the length of the pile, and the settlement on it is PL/AE. The offset is added to this elastic shortening, so that the Davisson line is at s = PL/AE + 0.15 + D/120 in inches. For piles of more than 24 in of diameter, the offset is D/30. The calculator gives the elastic part, the offset, the total and the slope.

How is the failure load found from the test?

Draw the load settlement curve of the test, then draw the Davisson line from the origin with the slope AE/L and shift it by the offset. The intersection of the two curves gives the Davisson failure load. The allowable load is then the failure load divided by a safety factor, often 2, or the design uses the resistance factor of the load and resistance factor design.

What are the limits of the calculator?

The calculator gives the line, not the intersection with the test curve. It assumes a uniform section and modulus of the pile, and the same load along the pile, while in reality the load decreases with the depth due to the shaft friction, so the real elastic shortening is lower. Test loading must be carried out and interpreted by a geotechnical engineer, according to the standard (ASTM D1143).

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.