Skip to content
Omnikalc

Pushover curve bilinear idealization and ductility calculator

Enter three points of a pushover curve, the design base shear and the period to get the equal-energy bilinear curve, the yield point, the displacement ductility, the overstrength and the reduction factors.

Updated on
Your inputs
in

Value out of range

kips

Value out of range

in

Value out of range

kips

Value out of range

in

Value out of range

kips

Value out of range

kips

Value out of range

s

Value out of range

s

Value out of range

Results

Displacement ductility

4.83

A ductile system
Elastic stiffness
300.0 kip/in
Yield strength of the bilinear curve
372.6 kips
Yield displacement
1.24 in
Overstrength
2.48
Ductility reduction factor
2.94
Total reduction factor
7.31

The pushover curve calculator replaces a capacity curve with an equal-energy bilinear curve and gives the yield point, the displacement ductility, the overstrength and the reduction factors of a building.

How the calculation works

  • Enter three points of the pushover curve: first yield, peak strength and the ultimate point, with the roof displacement and the base shear of each.
  • Enter the design base shear, the fundamental period and the corner period of the design spectrum.
  • The calculator gives the equal-energy bilinear curve, the displacement ductility, the overstrength and the reduction factors.

Example

A pushover analysis gives a first yield at 1.0 in and 300 kips, a peak of 420 kips at 3.0 in and an ultimate point of 336 kips at 6.0 in (80 percent of the peak). The area under the curve is 150 + 720 + 1,134 = 2,004 kip-in. The elastic stiffness is 300 / 1.0 = 300 kip/in. The equal-energy bilinear curve has a yield strength of Vy = k (δu − √(δu² − 2A / k)) = 372.6 kips, so the yield displacement is 1.24 in and the ductility is 6 / 1.24 = 4.83. With a design base shear of 150 kips, the overstrength is 2.48. For a period of 0.4 s, shorter than the corner period of 0.5 s, the ductility reduction factor is √(2μ − 1) = 2.94, and the total factor is 7.31.

Why it matters

The calculator helps structural engineers, researchers and students to read the result of a nonlinear static analysis, to compare it with the design base shear and to judge the ductility of a frame or a wall. The equal-energy rule is the one that most guidelines use for the idealization of the curve.

Good to know

Take the first-yield point where the curve leaves the straight line, the peak at the maximum base shear and the ultimate point where the strength has fallen by 20 percent or where the drift limit is reached. The vertical shear must be on the same basis as the design shear. A ductility below 2 means that the structure should be designed as an elastic one. Check that the peak lies below the elastic line: otherwise the area is too large for the stiffness, and the calculator keeps the square root real.

The seismic base shear calculator gives the design shear, the story drift calculator checks the drift and the stability coefficient, the Vs30 site class calculator gives the site class of the spectrum and the portal frame calculator gives the drift of a simple frame.

Frequently asked questions

What is the bilinear idealization of a pushover curve?

A pushover curve is the base shear plotted against the roof displacement as a structure is pushed laterally to failure. It is smooth, so engineers replace it with an elastic-perfectly-plastic curve that has the same area. The initial stiffness is kept, and the yield strength is found so that the energy under the two curves is equal, which gives Vy = k (δu − √(δu² − 2A / k)).

What do ductility and overstrength mean?

The displacement ductility is the ultimate displacement divided by the yield displacement of the bilinear curve. It measures how far the structure can deform after yield. The overstrength is the yield strength divided by the design base shear, and it measures the reserve of strength that the design does not count on, from the material strength, the code minimums and the load factors.

How is the reduction factor found?

For a structure with a period longer than the corner period, the equal displacement rule gives a reduction factor Rμ equal to the ductility μ. For a short period, the calculator uses the Newmark-Hall relation Rμ = √(2μ − 1) in the US version. The total factor R is the product of the overstrength and the ductility reduction. It is a way to compare a pushover with the R factor of a code.

What does the calculator leave out?

The calculator leaves out the shape of the load pattern, the degradation of the strength and the stiffness under cycles, the effect of the higher modes, the P-delta effect and the torsion. It takes three points of the curve that you pick. The result depends on those points, so use the same rules for all your comparisons and keep the ultimate point at the loss of 20 percent of the peak.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.