Skip to content
Omnikalc

Mat footing biaxial eccentricity and corner pressure calculator

Enter the vertical load, the moments about both axes and the size of the mat to get the eccentricities, the corner soil pressures, the kern check and the ratio to the allowable bearing pressure.

Updated on
Your inputs
kips

Value out of range

kip-ft

Value out of range

kip-ft

Value out of range

ft

Value out of range

ft

Value out of range

ksf

Value out of range

Results

Maximum corner pressure

3.69 ksf

Eccentricity along the length
2.50 ft
Eccentricity along the width
1.50 ft
Average pressure
2.50 ksf
Minimum corner pressure
1.31 ksf
The whole mat is in compression
Kern ratio (6ex/L + 6ey/B)
0.47
The resultant is inside the kern
Maximum pressure over the allowable
0.92
Within the allowable pressure

The mat footing calculator gives the soil pressure at the corners of a rectangular mat under a vertical load and moments about both axes, with the eccentricities, the kern check and the ratio to the allowable bearing pressure.

How the calculation works

  • Enter the vertical load with the weight of the mat, the moments about the two axes and the length and width of the mat.
  • Enter the allowable bearing pressure of the soil.
  • The calculator gives the eccentricities, the average, maximum and minimum corner pressures, the kern ratio and the ratio to the allowable pressure.

Example

A mat of 60 ft × 40 ft carries 6,000 kips with moments of 15,000 kip-ft and 9,000 kip-ft. The eccentricities are 2.50 ft and 1.50 ft. The average pressure is 6,000 / 2,400 = 2.50 ksf. The kern ratio is 6 × 2.50 / 60 + 6 × 1.50 / 40 = 0.475, so the resultant is inside the kern and the pressures are 2.50 × (1 ± 0.475): 3.69 ksf at the worst corner and 1.31 ksf at the opposite one. Against 4 ksf the ratio is 0.92.

Why it matters

The calculator helps structural and geotechnical engineers, builders and students to check a mat or raft under a tower, a tank or a tall building with wind or seismic moments, and to see how the size of the mat changes the pressure and the uplift.

Good to know

Include the weight of the mat, the soil on it and the water in the total load, and use the combination of loads that gives the worst case. Take the moments about the center of the mat. Check that the kern ratio is not above one for the service combinations, and that the maximum pressure is under the allowable value, which is often raised by a third for short-term wind or seismic loads in the code. A mat with a small uplift can be accepted for a short time load if the code allows it and the partial contact is analyzed, but not for the sustained load.

The bearing capacity calculator gives the ultimate pressure of the soil, the footing size calculator sizes a column footing, the combined footing calculator gives the reactions of two columns and the gravity wall calculator checks stability against overturning.

Frequently asked questions

What is the kern of a rectangle?

The kern, or middle third rule for a rectangle, is the zone of the base inside which a vertical load causes compression on the whole area. For a load with eccentricities ex along the length L and ey along the width B, the whole base is in compression when 6ex/L + 6ey/B ≤ 1. Beyond it a corner lifts off the soil and the pressure of the rest of the base rises.

How are the corner pressures found?

The pressure at a point is the average pressure P / (L × B) plus the effect of each moment, 6 ex / L and 6 ey / B times the average, with the sign of the side. The four corners have the combinations (+, +), (+, −), (−, +) and (−, −). The maximum is at the corner on the side of both moments, the minimum at the opposite one.

What if the resultant is outside the kern?

Then the formula gives a negative pressure at a corner, which the soil cannot take, and the real contact area is smaller with a higher maximum pressure. The calculator warns. You should enlarge the mat, reduce the eccentricity by moving the mat or the load, or analyze the partial contact with a more complete method.

What does the calculator leave out?

The calculator leaves out the settlement and the tilt of the mat, the stiffness of the mat and the soil, the case of a flexible mat with a nonlinear pressure, the groundwater and uplift, the overturning and sliding checks and the load combinations. It checks the rigid mat on a linear pressure.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.