Skip to content
Omnikalc

Forklift load center capacity derating calculator for long loads

Enter the rated capacity, the rated load center, the length of the load and its weight to get the actual load center, the derated capacity, the margin and the ratio of the load.

Updated on
Your inputs
lb

Value out of range

in

Value out of range

in

Value out of range

lb

Value out of range

Results

Ratio of the load to the derated capacity

0.95

The load is within the derated capacity
Actual load center
30 in
Derated capacity
4,000 lb
Capacity reduction
20.0 %
Margin over the load
200 lb

The forklift load center capacity derating calculator gives the actual load center, the derated capacity, the capacity reduction, the margin over the load and the ratio of the load to the derated capacity of a forklift carrying a long load, from the rated capacity, the rated load center, the length of the load and its weight.

How the calculation works

  • Enter the rated capacity and the rated load center of the forklift, from its data plate.
  • Enter the length of the load along the forks and its weight.
  • The calculator finds the actual load center, the derated capacity, the reduction, the margin and the ratio.

Example

A forklift is rated 5,000 lb at a 24 in load center. A load 60 in long has its center of gravity at 30 in from the face of the forks. The capacity is reduced to 5,000 × 24 / 30 = 4,000 lb, a reduction of 20.0 %. A load of 3,800 lb has a margin of 200 lb, and the ratio is 0.95.

Why it matters

The calculator helps forklift operators, site supervisors, safety officers and students to check if a long or bulky load, like a pipe bundle, a pallet of lumber or a precast element, can be lifted safely, and to decide on a larger forklift or on a shorter load.

Good to know

Read the data plate of the forklift before each lift and keep the load as close to the mast as possible. Lift the forks only as high as needed and travel with the load low and tilted back. Do not use a forklift for a load that is longer or higher than the data plate allows, and use a crane or a longer-reach machine when the load center is far from the forks.

The sling angle calculator gives the tension in the legs of a lift, the crane mat bearing pressure calculator checks the ground under a crane, the tower crane calculator checks the load moment of a lift and the dump truck loads calculator checks the payload of a truck.

Frequently asked questions

What is the load center of a forklift?

The load center is the horizontal distance from the vertical face of the forks to the center of gravity of the load. The rated capacity of a forklift, on its data plate, is given for a standard load center, 24 in (600 mm) for most forklifts. The forklift works as a lever around the front axle, so a load whose center is farther from the forks tilts the truck forward and needs a smaller weight.

How is the capacity reduced?

The capacity is inversely proportional to the load center, since the moment around the front axle must stay the same. For a load center of 30 in instead of 24 in, the capacity is 24 / 30 = 80 % of the rated one. For a uniform load, the center of gravity is at the middle of the length of the load, so a long load of 60 in has a load center of 30 in.

What else reduces the capacity?

The capacity also falls when the mast is raised high, because the center of gravity of the truck and the load rise and the stability decreases. It falls with an attachment, like a side shifter or a clamp, which adds weight and moves the center of the load forward. The data plate gives the real capacity with the attachments and at the height, and it must be read before the lift.

What are the limits of the calculator?

The calculator gives the capacity for a uniform load at a low height. It does not take into account the height of the lift, the attachments, the tilt of the mast, the slope and the roughness of the ground, the speed or the turns with a load. The operator must follow the data plate of the forklift and the rules of the manufacturer, and the load must be stable on the forks.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.