Skip to content
Omnikalc

Clevis pin shear calculator: check a pin in double shear and in bearing

Enter the load, pin diameter, plate and eye thicknesses, yield strengths and design factor to get the shear stress in the pin, the bearing stress on the plates and the eye, the utilization and the minimum pin diameter.

Updated on
Your inputs
lb

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

psi

Value out of range

Value out of range

Results

Governing utilization

74.1 %

Acceptable utilization for a static load
Shear stress in the pin (double shear)
6,366 psi
Shear utilization of the pin
36.8 %
Governing bearing stress
13,333 psi
Bearing utilization of the plates
74.1 %
Minimum pin diameter for shear
0.606 in

The clevis pin shear calculator checks a pin connection in double shear: it gives the shear stress in the pin, the bearing stress on the plates and the eye, the utilization against the allowable values and the minimum pin diameter.

How the calculation works

  • Enter the load on the pin, its diameter and the thicknesses of the clevis plates (each) and of the eye or rod end between them.
  • Enter the yield strengths of the pin and of the plates, and the design factor (2 for a static load, higher for shock or fatigue).
  • The calculator finds the shear stress in the pin in double shear τ = F / (2 × π d² / 4) and compares it with the allowable shear 0.577 Sy / n.
  • It checks the bearing stress on the eye (F / d t) and on the two plates (F / 2 d t), against Sy / n, and gives the governing utilization.

Example

A clevis pin of 1 in diameter carries 10,000 lb in double shear, between plates of 0.375 in around an eye of 1 in. The shear stress is 10,000 / (2 × 0.7854) = 6,366 psi, against an allowable of 0.577 × 60,000 / 2 = 17,310 psi, so the shear utilization is 36.8%. The bearing stress is 10,000 / (2 × 1 × 0.375) = 13,333 psi on the plates, against 36,000 / 2 = 18,000 psi, or 74.1%. The governing utilization is 74.1%, and the minimum pin diameter for shear is 0.606 in.

Why it matters

The calculator helps mechanical and structural designers, riggers, agricultural and construction equipment engineers and students to size or check a clevis pin, a hitch pin or a hinge pin. It also helps find which of the shear or the bearing governs, and to see how much margin there is.

Good to know

Use the real strength of the pin material and not the grade of the plate. Add a bending check when the gap between the plates is large. Use a higher design factor for shock loads, lifting and human safety. Keep a retaining pin or cotter in place, and replace pins with visible wear or deformation.

The bolt shear capacity calculator covers bolts in shear and bearing, the stress concentration factor calculator covers the effect of holes, the shaft torsion calculator covers twisting of a shaft and the Hertz contact stress calculator covers contact between curved bodies.

Frequently asked questions

What is double shear?

A pin in a clevis joint is cut by the load in two sections, one at each side of the eye, so the load is carried by twice the cross-section area of the pin. The shear stress is therefore half of what it would be in single shear: τ = F / (2 A). The pin can also fail by bending between the plates and by crushing of the pin or the holes, and each of these modes has to be checked.

What is the allowable shear stress?

For ductile steel, the shear yield strength is about 0.577 times the tensile yield strength, from the von Mises criterion. Dividing by the design factor gives the allowable shear stress. A factor of 2 is common for a static load with a known magnitude, and 3 or more for shock loads, uncertain loads, lifting or fatigue. Some codes use 0.4 Sy for the allowable shear with no further factor.

Why check the bearing stress?

The pin pushes on the sides of the holes in the plates and the eye with a pressure equal to the load divided by the projected area, which is the diameter times the thickness. If this pressure is too high, the holes elongate and the joint becomes loose. Thin plates around a large pin are often limited by bearing and not by the shear of the pin, as the default example shows.

What does the calculator not check?

It does not check the bending of the pin between the plates, which governs for a wide gap or a long pin, nor the tear-out of the plate at the edge of the hole, the tension at the net section of the plates, the fatigue at the holes or the wear for a rotating joint. These checks need the end distance and the width of the plates, and are made with a structural code.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.