Skip to content
Omnikalc

Liquefaction factor of safety calculator: simplified procedure for a sand layer in an earthquake

Enter the depth, the water table, the unit weights, the peak ground acceleration, the magnitude and the corrected SPT blow count to get the cyclic stress ratio, the cyclic resistance ratio and the factor of safety against liquefaction.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

lb/ft³

Value out of range

lb/ft³

Value out of range

Value out of range

Value out of range

Value out of range

Results

Factor of safety against liquefaction

1.19

Marginal: liquefaction is possible and the soil should be studied in detail
Total vertical stress
2,420 psf
Effective vertical stress
1,671 psf
Cyclic stress ratio (CSR)
0.135
Cyclic resistance ratio at the magnitude (CRR)
0.160

The liquefaction factor of safety calculator estimates whether a saturated sand layer will liquefy in an earthquake, with the simplified procedure of Seed and Idriss, from the depth, the water table, the peak acceleration, the magnitude and the SPT blow count.

How the calculation works

  • Enter the depth of the sand layer to check, the depth of the water table and the unit weights of the soil above and below it.
  • Enter the peak ground acceleration of the design earthquake as a fraction of g and its moment magnitude.
  • Enter the corrected SPT blow count (N1)60 of the layer, for clean sand.
  • The calculator finds the cyclic stress ratio of the simplified procedure of Seed and Idriss, the cyclic resistance ratio and the factor of safety FS = CRR / CSR.

Example

A sand layer at 20 ft has the water table at 8 ft, with unit weights of 115 and 125 lb/ft³. The total stress is 115 × 8 + 125 × 12 = 2,420 psf and the effective stress is 2,420 − 62.4 × 12 = 1,671 psf. With 0.15 g, magnitude 7.5 and (N1)60 = 15, the stress reduction factor is 0.953 and the CSR is 0.65 × 0.15 × (2,420 / 1,671.2) × 0.953 = 0.135. The CRR is 0.160, so the factor of safety is 1.19: marginal.

Why it matters

The calculator helps geotechnical and structural engineers, planners and students to screen a site for liquefaction hazard, to see the effect of the water table, the magnitude and the density of the soil and to decide whether a detailed study or a ground improvement is needed. It gives the three key numbers of the hand calculation.

Good to know

Check several depths and use the water table at its highest level. Use the (N1)60 corrected for the energy and the overburden, and make a correction for fines in silty sands. Use the peak acceleration of the design earthquake at the ground surface, including the site effects. A low blow count with a factor of safety near 1 needs a detailed study with CPT data and a deformation analysis.

The infinite slope stability calculator covers slopes, the seismic base shear calculator gives the earthquake force on a building, the Vs30 site class calculator gives the seismic site class and the piping safety factor calculator checks seepage failure.

Frequently asked questions

What is liquefaction?

Liquefaction is the loss of strength of a loose saturated sand or silt when it is shaken by an earthquake. The pore water pressure rises as the soil tries to compact, the effective stress falls to near zero and the soil behaves like a liquid. It can cause settlement, lateral spreading, sand boils and the loss of bearing capacity of foundations, as in Niigata in 1964 and Christchurch in 2011.

What is the simplified procedure?

The simplified procedure of Seed and Idriss compares the cyclic stress ratio CSR caused by the earthquake with the cyclic resistance ratio CRR of the soil. The CSR is 0.65 (amax / g) (σv / σ′v) rd, where rd reduces the stress with depth. The CRR for a magnitude of 7.5 comes from the SPT blow count, here with the equation fitted to the clean sand curve of Youd and Idriss, and is scaled with a magnitude scaling factor.

Which soils can liquefy?

Loose saturated sands and non-plastic silts are the most susceptible, mostly at shallow depths less than about 50 ft (15 m) and in young deposits. Clays are not liquefiable in the usual sense, and dense sands are resistant. The calculator is for clean sand. A correction for fines content increases the blow count equivalent for silty sands, and the CPT and shear wave velocity methods give independent estimates.

What factor of safety is needed?

A factor of safety of 1.0 or less indicates that liquefaction is expected. Values between 1.0 and 1.3 are marginal, and many agencies require at least 1.2 to 1.3 for the design earthquake, depending on the importance of the structure. When the factor is low, ground improvement by compaction, drains or deep foundations can be used. This calculation is a screening tool, and a geotechnical engineer must carry out the study.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.