Skip to content
Omnikalc

Mohr–Coulomb shear strength calculator

Enter the cohesion, the friction angle and the normal stress to get the shear strength of the soil, and the failure state in a triaxial test.

Updated on
Your inputs
psf

Value out of range

°

Value out of range

psf

Value out of range

psf

Value out of range

psf

Value out of range

Results

Shear strength τf

1,555 psf

Safety factor against shearing

1.55

Frictional part σ·tan φ
1,155 psf
Angle of the failure plane to the major principal plane
60.0 °
Major principal stress σ1 at failure
5,886 psf
Unconfined compressive strength qu
1,386 psf

The Mohr–Coulomb shear strength calculator gives the shear strength of a soil, its frictional part, the safety factor against shearing, the failure plane angle, the major principal stress at failure and the unconfined compressive strength.

How the calculation works

  • Enter the cohesion and the friction angle of the soil.
  • Enter the effective normal stress and the shear stress applied on the plane.
  • Enter the confining stress σ3 of a triaxial test to get the stress at failure.

Example

A soil with a cohesion of 400 psf and a friction angle of 30 °, under a normal stress of 2000 psf, has a shear strength of 1,555 psf, of which 1,155 psf is friction. Against an applied shear of 1000 psf the safety factor is 1.55. In a triaxial test with σ3 of 1500 psf, failure occurs at 5,886 psf, on a plane at 60.0 °.

Why it matters

The calculator helps students of soil mechanics and engineers who check the strength of a soil on a slip plane, interpret laboratory tests or estimate the stress at which a sample fails under confinement.

Good to know

Use effective stresses, and the c and φ from drained tests, for long-term problems. For short-term undrained loading of saturated clay, a total-stress analysis uses φ = 0 and the undrained shear strength as cohesion. The linear envelope fits a limited range of stress, so use values measured for the stress level of the problem. The criterion ignores the intermediate principal stress, anisotropy and strain softening. Results depend strongly on the soil parameters, so a design needs site investigation and a geotechnical engineer.

The effective stress calculator gives the stress carried by the soil skeleton, the principal stress calculator finds principal values, the gravity wall stability calculator checks sliding and overturning and the infinite slope calculator evaluates slope stability.

Frequently asked questions

What is the Mohr–Coulomb criterion?

It states that the shear strength of a soil on a plane is τf = c + σ′ tan φ, where c is the cohesion, σ′ the effective normal stress on the plane and φ the friction angle. Failure occurs when the shear stress on some plane reaches this strength. It is the standard model for the strength of soils and rocks in geotechnical engineering.

How are c and φ determined?

From laboratory tests, such as direct shear and triaxial tests, or from in-situ tests and correlations. Clean sands and gravels have c close to zero and friction angles of about 28 to 40 degrees. Clays have cohesion and lower friction angles, and the values depend on drained or undrained conditions and on the effective stresses.

What is the failure plane angle?

At failure, the failure plane makes an angle of 45° + φ/2 with the plane of the major principal stress. For a purely cohesive soil with φ = 0, the angle is 45 degrees. The unconfined compressive strength is qu = 2 c tan(45° + φ/2), which for φ = 0 is 2c.

What does the safety factor tell?

It is the ratio of the shear strength on the plane to the shear stress applied on it. Values above 1 mean that the plane is stable, with design codes asking for margins that depend on the structure, such as 1.5 for many slopes and walls. Pore pressure lowers the effective stress and the strength, so it must be accounted for.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.