Skip to content
Omnikalc

Channel lining tractive force calculator: how big must the riprap of a channel be?

Enter the depth of flow, the slope, the side slope, the Shields parameter and the safety factor to get the shear stress on the bed and the banks, the side slope factor and the riprap D50 needed on the bed and on the side slope.

Updated on
Your inputs
ft

Value out of range

ft/ft

Value out of range

Value out of range

Value out of range

Results

Riprap D50 required on the side slope

7.4 in

Maximum shear stress on the bed
1.87 lb/ft²
Maximum shear stress on the side slope
1.42 lb/ft²
Side slope factor K
0.718
Riprap D50 required on the bed
7.0 in

The channel lining tractive force calculator gives the shear stress on the bed and the banks of an open channel and the riprap size D50 needed to resist it, from the depth of flow, the slope, the side slope and the Shields parameter.

How the calculation works

  • Enter the depth of flow and the slope of the channel, for the design discharge.
  • Choose the side slope of the banks. The riprap on a steep bank is less stable, so a side slope factor K is applied (angle of repose of 40°).
  • Enter the Shields parameter (about 0.047 for a turbulent flow) and a safety factor.
  • The calculator finds the shear stress on the bed (γ d S) and on the side slope (0.76 of the bed), and the median size D50 of the riprap needed for each.

Example

A channel has a depth of flow of 3 ft and a slope of 0.01. The maximum shear on the bed is 62.4 × 3 × 0.01 = 1.87 lb/ft² and on the side slope it is 0.76 × 1.87 = 1.42 lb/ft². With 2H : 1V banks, K = 0.718. With Shields = 0.047 and a safety factor of 1.5, the D50 needed on the bed is 12 × 1.5 × 1.87 / (0.047 × 1.65 × 62.4) = 7.0 in, and 7.4 in on the side slope.

Why it matters

The calculator helps civil and environmental engineers, drainage designers, contractors and students to choose the size of the stones that protect a ditch or a channel from erosion, to compare the bed with the banks and to see the effect of the slope and of the depth. It is a first step before the detailed design of the lining.

Good to know

Use the depth of the design flood and the slope of the energy grade, not only that of the bed. Increase the shear in the bends and downstream of structures. Provide a filter layer, a thickness of at least twice the D50 and a toe protection, and check the stability of the lining at the transitions.

The Manning equation calculator gives the depth and the velocity of the flow, the riprap calculator sizes the stone of a slope, the critical depth calculator checks the flow regime and the bridge pier scour calculator covers the scour at a pier.

Frequently asked questions

What is the tractive force method?

The tractive force, or shear stress, is the force of the flowing water on the bed and the banks of a channel per unit area. It is τ = γ d S, the unit weight of the water times the depth and the slope. A lining is stable when the shear stress is lower than its permissible shear stress, which depends on the material: sand and silt resist a few hundredths of a pound per square foot, and riprap resists much more, in proportion to its size.

Why is the shear less on the banks?

In a trapezoidal channel the maximum shear on the bed is about γ d S, but on the banks it is only about 0.76 of this value because the flow is slower near the sides. On the other hand the stones of a bank can roll down the slope under their weight, so their resistance is reduced by a factor K that decreases when the slope gets steeper. For 2H : 1V, K is about 0.72.

How is the riprap size found?

The calculator uses the Shields equation, τ = θ (γs − γ) D50 for the stability of a stone, with a safety factor. For stones with a specific gravity of 2.65 and θ = 0.047, the required D50 is about τ / (0.077 γ) times the safety factor, in the same units. HEC-15 and HEC-23 give more complete methods with the shape of the channel, the bends and the filter or the geotextile under the stone.

What are the limits of the calculator?

The calculator gives the size of the stone for a straight channel with a uniform flow. It does not include the bends, which increase the shear, the steep slopes above 10%, the gradation and the thickness of the riprap layer, the filter, the edge of the lining, the sediment or the debris. The design of an erosion protection must be made by a hydraulic engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.