Skip to content
Omnikalc

Planar rock slope failure factor of safety calculator

Enter the slope geometry, the tension crack, the water, the strength of the failure plane and the rock weight to get the factor of safety of a planar rock slope failure.

Updated on
Your inputs
ft

Value out of range

°

Value out of range

°

Value out of range

ft

Value out of range

ft

Value out of range

psf

Value out of range

°

Value out of range

pcf

Value out of range

Results

Factor of safety

1.19

Between 1 and 1.3: marginal, with little reserve
Length of the failure plane
104.6 ft
Weight of the sliding block per foot of slope
389,908 lb/ft
Water uplift on the failure plane
32,637 lb/ft
Water thrust in the tension crack
3,120 lb/ft
Factor of safety with a dry crack
1.29
Between 1 and 1.3: marginal, with little reserve

The planar rock slope failure calculator gives the factor of safety of a rock block that slides on a single plane, with a tension crack at the top and water in the crack, and shows the weight of the block and the water forces.

How the calculation works

  • Enter the slope height, the face angle, the dip of the failure plane and the depth of the tension crack.
  • Enter the water depth in the crack, the cohesion and friction angle of the plane and the unit weights.
  • The calculator gives the weight of the block, the water forces, the factor of safety and the factor of safety with a dry crack.

Example

A rock slope is 80 ft high with a face of 60°, a failure plane dipping 35°, a tension crack 20 ft deep holding 10 ft of water, a cohesion of 1,000 psf, a friction angle of 30° and a rock of 160 pcf. The failure plane is 104.6 ft long and the block weighs 389,908 lb per foot of slope. Water gives an uplift of 32,637 lb/ft and a thrust of 3,120 lb/ft. The factor of safety is 1.19, and 1.29 with a dry crack.

Why it matters

The calculator helps geotechnical engineers, mining engineers, road builders and students to check a rock cut, to see how water and the depth of the tension crack reduce the safety, and to compare the effect of a flatter face or a drain.

Good to know

The failure plane must dip out of the face and be steeper than its friction angle for the block to slide. Use the dip of the real joint or bedding plane, measured on site, and the cohesion and friction angle from tests or from experience with similar joints, and use a low cohesion if the joints are open. Check the factor of safety with the crack dry and with water, since a heavy rain can fill the crack. Add a margin for earthquakes and for the uncertainty of the data, and consider a flatter slope, drains or anchors when the factor of safety is low.

The infinite slope calculator checks a long soil slope, the soil nail pullout calculator sizes the nails of a wall, the tunnel rock support calculator classifies the rock with the Q system and the blast hole calculator gives the charge for the rock.

Frequently asked questions

What is planar failure?

A planar failure is the sliding of a block of rock along a single plane, such as a bedding plane or a joint, that dips out of the slope face at an angle that is less than the face angle and greater than the friction angle. A tension crack at the top of the slope separates the block from the rock behind it.

What are the formulas?

The factor of safety is the resisting force divided by the driving force along the plane: FS = (cA + (W cos ψp − U − V sin ψp) tan φ) / (W sin ψp + V cos ψp). W is the weight of the block, A the length of the plane, U the water uplift on the plane and V the water thrust in the tension crack. This is the classic method of Hoek and Bray.

Why does water matter so much?

Water in the tension crack pushes the block down the slope, and water on the failure plane lifts the block and reduces the friction. Both lower the factor of safety. Drainage with horizontal drains, or a surface ditch that keeps water out of the crack, is often the most economical way to raise the factor of safety.

What does the calculator leave out?

The calculator leaves out earthquake and blasting loads, the loads of bolts and anchors, a tension crack in the face, a slope with a bench, the roughness of the plane and the three-dimensional effects of a wedge. The model is in two dimensions, and the strength of the plane should come from tests, not from tables alone.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.