Skip to content
Omnikalc

Prestressed beam stress calculator: service stresses in a prestressed concrete beam

Enter the prestress force, the section properties, the eccentricity, the bending moment and the concrete strength to get the stresses at the top and the bottom fibers and the ratios to the allowable compression and tension.

Updated on
Your inputs
kips

Value out of range

in²

Value out of range

in⁴

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

kip-ft

Value out of range

ksi

Value out of range

Results

Stress at the bottom fiber (compression positive)

1.354 ksi

Stress at the top fiber (compression positive)
0.729 ksi
Largest compression over the limit 0.6 f′c
0.45
The compression is within the limit of 0.6 f′c
Tension over the tensile limit 7.5√f′c
0.00
The section is fully in compression

The prestressed beam stress calculator gives the stresses at the top and bottom fibers of a prestressed concrete section from the prestress force, the eccentricity, the section properties and the bending moment, and compares them with the allowable compression and tension.

How the calculation works

  • Enter the effective prestress force P after the losses, the area and moment of inertia of the section and the distances to the top and bottom fibers.
  • Enter the eccentricity of the tendons below the centroid and the bending moment at the section.
  • Enter the concrete strength f′c to compare the stresses with the allowable limits.
  • The calculator finds the stresses σ = P / A ∓ P e c / I ± M c / I at the top and the bottom fibers, and the ratios to the limits 0.6 f′c and 7.5√f′c.

Example

A rectangular beam of 12 in × 24 in (A = 288 in², I = 13,824 in⁴) carries a prestress of 300 kips at an eccentricity of 6 in, with a moment of 120 kip-ft at the section and f′c = 5 ksi. The top stress is 300 / 288 − 300 × 6 × 12 / 13,824 + 1,440 × 12 / 13,824 = 0.729 ksi of compression. The bottom stress is 1.042 + 1.563 − 1.250 = 1.354 ksi of compression. The largest compression is 0.45 of the limit 0.6 f′c = 3 ksi, and there is no tension.

Why it matters

The calculator helps structural engineers, precast designers and students to check the stresses of a prestressed beam or slab, to see the effect of the eccentricity and of the force on the top and bottom stresses and to size the prestress for a given moment. It reproduces the hand calculation of the elastic stress check.

Good to know

Check the section at transfer and under service loads, with the right moment for each case, and at the critical sections such as midspan and the supports. Use the effective force after losses for service, and the initial force at transfer. Keep the sign convention and the units consistent. Verify the strength, shear and deflection, and have the design verified by a licensed engineer.

The tendon friction loss calculator gives a prestress loss, the beam deflection calculator checks deflection, the concrete crack width calculator checks cracking and the concrete curing calculator covers curing.

Frequently asked questions

How does prestressing work?

A prestressed concrete member is compressed by high-strength tendons before it carries its load. The compression offsets the tension caused by the loads, which concrete resists poorly, so the member can span farther and be thinner than a reinforced one, and it stays uncracked under service loads. The tendons are placed below the centroid in a simple beam, to produce a moment opposite to the load moment.

What is the stress formula?

For the elastic stresses in a section under a prestress force P at an eccentricity e and a moment M, the stress at a fiber at a distance c from the centroid is σ = P / A ± P e c / I ∓ M c / I. The first term is the uniform compression, the second is the bending of the eccentric force, which compresses the bottom and unloads the top, and the third is the effect of the load moment, which does the opposite.

What are the allowable stresses?

The ACI 318 sets for service loads a limit of compression of 0.60 f′c, and a classification of the member by the tensile stress: class U (uncracked) members have a tension up to 7.5√f′c in psi, class T are transition members up to 12√f′c, and class C are cracked. The limits at transfer of the force are stricter and use the strength at that time. This calculator checks the class U limits.

What are the limits of this calculator?

It is a section-level elastic check at a single stage with the effective prestress after losses, and it does not include the losses of prestress from friction, shrinkage, creep and relaxation, which are found separately. It also does not compute the strength of the section, the shear or the deflection. Check the stresses at transfer, with the self-weight only and the initial force, and at the service load.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.