Skip to content
Omnikalc

Portal frame lateral load and drift calculator

Enter the lateral load, the column height and spacing, the column inertia and the type of base to get the column shear and moments, the axial force from overturning and the lateral drift of a portal frame.

Updated on
Your inputs
kips

Value out of range

ft

Value out of range

ft

Value out of range

in⁴

Value out of range

ksi

Value out of range

Results

Moment at the top of a column

70.0 kip-ft

Shear in each column
10.0 kips
Moment at the base of a column
70.0 kip-ft
Axial force in the columns from overturning
11.7 kips
Lateral drift of the girder
0.281 in
Drift ratio (height over drift)
598
Stiff: within the usual limit for wind of about H/400

The portal frame calculator gives the column shear, the column moments, the axial force from overturning and the lateral drift of a one bay frame with a rigid girder under a lateral load, with fixed or pinned bases.

How the calculation works

  • Enter the lateral load at the girder, the height and the spacing of the columns, their moment of inertia and the modulus.
  • Choose fixed or pinned column bases.
  • The calculator gives the column shear, the moments at the top and at the base, the axial force from overturning and the lateral drift.

Example

A portal frame with columns 14 ft high and 24 ft apart takes a lateral load of 20 kips at the girder. With fixed bases and a rigid girder, each column takes 10 kips, and the inflection point is at mid-height, so the moments at the top and at the base are 10 × 14 / 2 = 70 kip-ft. The overturning gives an axial force of 20 × 14 / 24 = 11.67 kips in each column, up on one side and down on the other. With columns of 485 in⁴, the drift is 0.28 in, or H/598. With pinned bases the top moment doubles to 140 kip-ft and the drift is 1.12 in.

Why it matters

The calculator helps structural engineers, builders of steel buildings and students to estimate the forces in a frame under wind or seismic load, to compare fixed and pinned bases and to check the drift before a detailed analysis.

Good to know

Treat the results as a first estimate. A real girder bends, so the columns see more moment at the top and the frame drifts more than the rigid girder model. If the girder is not at least four to five times stiffer than the column, use a frame analysis. Take the bases as fixed only if the footing and the base plate can resist the moment, which is rarely true of a light base plate. Add the effect of the gravity load to the axial force, and check the column for the axial load with the moment.

The seismic base shear calculator gives the lateral load of an earthquake, the story drift calculator checks the second-order effect, the effective length calculator gives the K factor of a column and the steel column capacity calculator checks the axial capacity.

Frequently asked questions

What is the portal method?

The portal method is a simple approximate analysis of a frame under lateral load. It assumes that the girder is much stiffer than the columns, so that the columns bend in double curvature with an inflection point at mid-height, and that the lateral load is shared between the columns. The column shear, the moments and the axial forces then follow from statics alone.

Why do the moments double with pinned bases?

With fixed bases, each column has an inflection point at mid-height, and the moment is Vh/2 at the top and at the base. With pinned bases, the moment at the base is zero, and the whole Vh goes to the top of the column. The girder and the joint must then resist twice the moment, and the frame is four times more flexible.

How is the drift found?

With a rigid girder, each column acts like a cantilever guided at the top. The drift is Vh³/(12EI) for fixed bases, which is Hh³/(24EI) for the two columns. For pinned bases the column is a cantilever with a moment at the top only, and the drift is Vh³/(3EI), four times larger.

What does the calculator leave out?

The calculator assumes an infinitely stiff girder, equal columns, no axial deformation, no panel zone and no second-order effect. A real girder is flexible, so the real moments in the columns and the real drift are larger. Use a frame analysis for design, and this tool for a first estimate or a check.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.