Skip to content
Omnikalc

Railroad track ballast, ties and rail quantity calculator

Enter the length of track, the tie spacing, the rail weight and the ballast section to get the number of ties, the rail and ballast weights, the volume of ballast and the tie plates.

Updated on
Your inputs
mi

Value out of range

in

Value out of range

lb/yd

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Value out of range

lb/ft³

Value out of range

Results

Number of ties

8,124

Weight of ballast

8,250 tons

Weight of rail, two rails
506.0 tons
Volume of ballast
6,111 yd³
Number of tie plates
16,248

The railroad track materials calculator gives the number of ties, the weight of rail, the volume and weight of ballast and the tie plates for a length of track, from the tie spacing, the weight of the rail and the section of the ballast.

How the calculation works

  • Enter the length of track, the tie spacing, the weight of the rail and the length of the ties.
  • Enter the ballast section: shoulder, depth, side slope and bulk density.
  • The calculator finds the number of ties, the weight of rail, the volume and weight of ballast and the tie plates.

Example

A track of 2.5 mi with ties every 19.5 in. needs 2.5 × 63,360 / 19.5 = 8,123.1, rounded up to 8,124 ties, and 16,248 tie plates. Two rails of 115 lb/yd weigh 2.5 × 1,760 × 2 × 115 / 2,000 = 506 tons. A ballast section of ties of 8.5 ft with a 1 ft shoulder, a depth of 1 ft and a slope of 2 to 1 has an area of 12.5 ft², so the track needs 6,111 yd³, that is 8,250 tons of ballast at 100 lb/ft³.

Why it matters

The calculator helps railroad engineers, track contractors, industrial rail owners, estimators and students to list the main materials of a track project, to compare the effect of the tie spacing and the ballast section, and to plan the delivery and the hauling.

Good to know

Use the standard of the owner for the tie spacing, the rail and the ballast section, and add the waste to the quantities: 5 percent for ties and plates, and 10 percent for the ballast, which also compacts under traffic. Order the ballast by weight from a quarry and check its gradation. Use the bulk density from the quarry and not the generic 100 lb/ft³.

The gravel driveway calculator gives the stone for a road, the geogrid base reinforcement calculator gives the rolls of geogrid, the dump truck loads calculator gives the loads to haul the ballast and the compaction roller production calculator gives the area compacted per hour.

Frequently asked questions

How many ties per mile?

The number of ties per mile is 5,280 ft times 12 in. divided by the spacing in inches. A common spacing of 19.5 in. gives about 3,250 ties per mile, and a closer spacing of 18 in. gives about 3,520. Main line tracks of heavy haul railroads use the closer spacing, and branch lines and yards use fewer, with spacings up to 24 in. The calculator rounds the count of ties up.

How is the weight of rail found?

Rail is sold by the weight per yard. A mile of track has two rails of 1,760 yd each, so with a rail of 115 lb/yd it weighs 2 × 1,760 × 115 / 2,000 = 202.4 tons per mile. Common rail sizes are 115 RE and 136 RE for main lines, and 90 to 100 lb for lighter lines. Add the weight of the joint bars, the bolts and the welds if you need the full material list.

How is the ballast section defined?

Ballast is placed as a trapezoid around the ties: the top width is the length of the tie plus a shoulder at each end, the depth under the tie is typically 8 to 12 in. for a main line, and the sides slope at 1.5 to 2 horizontal to 1 vertical. The calculator takes the section below the bottom of the tie. The cribs between the ties and above the tie bottom are an extra volume that depends on the profile.

What does the calculator leave out?

The calculator does not include the sub-ballast, the subgrade, the turnouts and the crossings, the curves with a wider shoulder, the lifting and tamping, the spikes, the clips and the anchors, or the waste of the ballast on the delivery. Add 5 to 10 percent to the ballast, and take the details from the standard of the railroad or the specification of your project.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.