Skip to content
Omnikalc

Stirrup spacing calculator: shear reinforcement of a concrete beam

Enter the factored shear, the beam section, the concrete and steel strengths and the stirrup area to get the shear carried by the concrete and the stirrups, the spacing needed, the code maximum and the spacing to use.

Updated on
Your inputs
kips

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

psi

Value out of range

in²

Value out of range

Results

Spacing to use (rounded down to 0.5 in)

5.0 in

Shear carried by the concrete Vc
30.4 kips
Shear to be carried by the stirrups Vs
49.6 kips
Spacing needed by the shear
5.32 in
Maximum spacing allowed by the code
10.0 in
Vs over the section limit (8 √f’c b d)
0.41
Comfortable shear demand

Stirrups are the loops of steel that carry the shear in a reinforced concrete beam. The stirrup spacing calculator gives the shear carried by the concrete and by the stirrups, the spacing needed, the maximum spacing of the code and the spacing to use, with the ACI 318 method.

How the calculation works

  • Enter the factored shear force Vu at the section (at the distance d from the face of the support), the width b and the effective depth d of the beam.
  • Enter the concrete strength f’c, the yield strength fy of the stirrups and the area Av of the legs of one stirrup (two legs of a No. 3 bar are 0.22 in²).
  • The calculator takes the concrete contribution Vc = 2 √f’c b d, with the strength reduction factor 0.75, and computes the shear that the stirrups carry: Vs = Vu / 0.75 − Vc.
  • Read the spacing needed s = Av fy d / Vs, the maximum spacing of the code (d/2 up to 24 in, d/4 up to 12 in) and the spacing to use.

Example

A beam 12 in wide with an effective depth of 20 in, concrete of 4,000 psi and No. 3 stirrups (Av = 0.22 in², fy = 60,000 psi) carries Vu = 60 kips. The concrete carries Vc = 2 × √4,000 × 12 × 20 = 30.4 kips. The stirrups must carry Vs = 60 / 0.75 − 30.4 = 49.6 kips. The spacing is 0.22 × 60,000 × 20 / 49,640 = 5.32 in, below the maximum of 10 in (d/2). The spacing to use is 5.0 in. Vs is 41% of the section limit, so the section is adequate.

Why it matters

The calculator helps civil and structural engineering students, designers and builders to size the shear reinforcement of a beam, to check a drawing or to understand how the spacing changes with the shear and the section. It gives the answer of the hand calculation in a few seconds.

Good to know

Compute the shear at the distance d from the support face, and vary the spacing along the beam: tighter near the supports, wider at the middle. Round the spacing down to a practical value. Check that the area of one stirrup is the area of both legs, and that the bars and the hooks are detailed as the code requires.

The rebar development length calculator gives the anchorage of the bars, the cracking moment calculator checks the flexure, the punching shear calculator covers the slabs and the beam deflection calculator checks the serviceability.

Frequently asked questions

How is the shear reinforcement designed?

In the strength design method of ACI 318, the factored shear Vu must not exceed φ (Vc + Vs), with φ = 0.75. The concrete carries Vc = 2 √f’c b d. The rest, Vs = Vu / φ − Vc, is carried by the stirrups, which cross the diagonal cracks. For vertical stirrups of area Av at spacing s, the shear they carry is Vs = Av fy d / s, so the spacing is s = Av fy d / Vs.

What is the maximum spacing?

To make sure that every diagonal crack is crossed by at least one stirrup, the spacing is limited to d/2 or 24 in when Vs is not more than 4 √f’c b d. When Vs is larger, the limits are halved, to d/4 or 12 in. The calculator applies these limits and shows the one that governs. Some codes also require a minimum area of stirrups, even when the concrete alone is enough.

What does the section limit mean?

If Vs exceeds 8 √f’c b d, the concrete of the web would crush before the stirrups yield, and no spacing is enough. The only fixes are a larger section or a stronger concrete. The calculator shows the ratio of Vs to this limit: above 1 the section is too small, and above 0.5 the stirrups are heavily loaded and the detailing needs care.

Does this replace a structural design?

No. It is a first check for a beam under a uniform load and a shear at the critical section. The design of a real beam also needs the flexure, the anchorage, the minimum stirrups, the torsion, the seismic detailing and the load cases. Have a licensed engineer check any structure that is built, and follow the local code.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.