Skip to content
Omnikalc

Reinforced concrete corbel design calculator

Enter the vertical load, the horizontal tension, the shear span and the corbel size to get the flexure, direct tension and shear friction steel, the main tension steel, the stirrups and the shear limit of ACI 318.

Updated on
Your inputs
kips

Value out of range

kips

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

psi

Value out of range

Results

Main tension steel Asc

1.50 in²

Flexure steel Af
0.83 in²
Direct tension steel An
0.44 in²
Shear friction steel Avf
1.59 in²
Horizontal stirrup steel Ah
0.53 in²
Design shear strength limit
166.3 kips
Demand over the shear limit
0.60
The corbel is within the shear limit
Shear span over depth
0.33
The corbel provisions apply (a/d of 1 or less)

The corbel design calculator gives the flexure, direct tension and shear friction steel of a reinforced concrete corbel by ACI 318, the main tension steel, the horizontal stirrups and the check of the shear limit.

How the calculation works

  • Enter the factored vertical load and the horizontal tension, the shear span and the depth and width of the corbel.
  • Enter the concrete strength and the steel yield strength.
  • The calculator gives the flexure, direct tension and shear friction steel, the main tension steel, the horizontal stirrups and the check of the shear limit.

Example

A corbel 14 in wide with d = 18 in and h = 21 in carries 100 kips at 6 in from the face, with a horizontal tension of 20 kips, in 5,000 psi concrete and Grade 60 steel. The moment is 100 × 6 + 20 × 3 = 660 kip-in, which needs Af = 0.83 in². The direct tension needs An = 20 / (0.75 × 60) = 0.44 in² and the shear friction Avf = 100 / (0.75 × 1.4 × 60) = 1.59 in². The main steel is the largest of Af + An, ⅔ Avf + An and the minimum: 1.50 in². The stirrups are 0.5 × (1.50 − 0.44) = 0.53 in², and the design shear limit is 166 kips.

Why it matters

The calculator helps structural engineers, precast designers and students to size the brackets that carry beams and crane girders from columns and walls, and to see which of flexure, tension or shear friction governs.

Good to know

Check first that the shear span over the depth is not above one, and that the depth at the outer edge of the bearing is at least half of the depth at the face. Use the horizontal force from the bearing pad, such as the friction of a pad or the shrinkage of a precast beam, and not less than 0.2 Vu. Anchor the main bars at the front edge by welding them to a cross bar or an angle, or by a hook in the plane of the bar, and check the bearing under the pad. Place the closed stirrups in the upper two thirds of the depth.

The shear friction calculator checks the shear across a crack, the rebar development length calculator gives the anchorage of bars, the reinforced concrete beam calculator gives the flexural capacity and the punching shear calculator checks a slab at a column.

Frequently asked questions

What is a corbel?

A corbel is a short cantilever bracket that sticks out from a column or a wall to support a beam, a girder or a crane rail. The shear span a is the distance from the load to the face of the support and is at most the effective depth, so the corbel works as a deep member with a strut and a tie, not as a beam, and shear friction governs.

How is the steel found?

ACI 318 asks for three amounts. Af resists the moment of the vertical load and of the horizontal force, An resists the horizontal tension, and Avf is the shear friction steel across the crack at the face. The main tension steel is the largest of Af + An, two thirds of Avf plus An, and a minimum of 0.04 f'c / fy times b d. Closed stirrups of half the extra steel go in the upper two thirds of the depth.

Why is there a minimum horizontal tension?

A bearing pad restrains the movement of the beam end, shrinkage and temperature create a horizontal force even without applied load. ACI therefore asks for a horizontal tension Nuc of at least 0.2 Vu unless special provisions are made to avoid it. The calculator uses the larger of the value you enter and 0.2 Vu.

What does the calculator leave out?

The calculator leaves out the bearing area of the pad, the anchorage of the main bars at the front edge, with a weld or a hook, the check of the column or wall behind, lightweight concrete, and the dynamic effects. A corbel with a/d above 1 needs a different method. Detail the main bars to develop their strength at the face and the front edge.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.