Skip to content
Omnikalc

Seismic refraction depth to rock calculator by crossover distance

Enter the two layer velocities and the crossover distance of the travel-time graph to get the depth to rock, the intercept time and the ripping class of the rock.

Updated on
Your inputs
ft/s

Value out of range

ft/s

Value out of range

ft

Value out of range

Results

Depth to the top of the lower layer

23.7 ft

Intercept time
30.8 ms
Critical distance
11.3 ft
Ripping class of the lower layer
3
Marginal: ripping is slow, blasting may be needed

The seismic refraction calculator gives the depth to the lower layer from the crossover distance and the two velocities, the intercept time, the critical distance and the ripping class of the rock.

How the calculation works

  • Enter the velocity of the upper layer and the velocity of the lower layer from the slopes of the travel-time graph.
  • Enter the crossover distance, where the two lines of the graph meet.
  • The calculator gives the depth to the lower layer, the intercept time, the critical distance and the ripping class.

Example

A refraction survey gives a velocity of 1,500 ft/s for the soil and 6,500 ft/s for the rock, and the two lines of the graph cross at 60 ft. The depth is z = (xc / 2) √((v2 − v1) / (v2 + v1)) = 23.7 ft. The intercept time of the lower line is 30.8 ms and the critical distance is 11.2 ft. A rock velocity of 6,500 ft/s is in the class 3, marginal for a heavy ripper.

Why it matters

The calculator helps geotechnical engineers, geophysicists, contractors and students to turn a travel-time graph into a depth to rock, to check an interpretation with the intercept time and to judge whether the rock can be ripped or must be blasted.

Good to know

Read the slopes of the graph carefully, with enough geophones on each line. Run the survey in both directions to detect a dipping contact, and compare the depth with a borehole or a test pit. Treat a rock velocity as an indication of excavation difficulty only, together with the fracturing and the machine. Remember that a thin layer or a hidden layer is not seen by the method.

The seismic wave velocity calculator gives the speed of a wave in a material, the tunnel rock support calculator rates rock with the Q system, the blast hole charge calculator gives the powder factor and the earthwork swell and shrink calculator converts excavated volumes.

Frequently asked questions

What is a seismic refraction survey?

A hammer or a small charge sends a wave through the ground, and a line of geophones records the first arrival at increasing distances. Near the source the first wave is the direct one in the upper layer. Beyond a certain distance the wave that has traveled down to a faster layer, along it and back up arrives first. The graph of arrival time against distance shows two lines, one for each layer, and their slopes are the inverse of the velocities.

How does the crossover distance give the depth?

At the crossover distance, the direct wave and the refracted wave arrive at the same time. For two layers with a flat contact, this gives z = (xc / 2) √((v2 − v1) / (v2 + v1)). The depth can also be found from the intercept time of the second line, ti = 2 z √(v2² − v1²) / (v1 v2), and the calculator shows this time as a check against the graph.

What does the ripping class mean?

The velocity of the rock is a rough measure of how hard it is to excavate. Below about 3,000 ft/s (900 m/s) the material is easy to rip, up to 6,000 ft/s (1,800 m/s) a heavy ripper works, around 6,000 to 7,500 ft/s (1,800 to 2,300 m/s) the work is marginal, and above that the rock is usually blasted. The class is indicative and depends on the rock type, fracturing and the machine.

What are the limits of the method?

The formula assumes two layers with a flat contact, with the velocity increasing with depth and a lower layer thick enough to be seen. A hidden layer, a slower layer under a faster one, a dipping contact and a rough surface of the rock all break these assumptions. Use more shots, forward and reverse, and a full interpretation for a project, and confirm with a borehole or a test pit.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.