Skip to content
Omnikalc

Steel block shear rupture capacity calculator

Enter the plate thickness, the bolts, the edge distances, Fy and Fu to get the net areas, the AISC block shear strength and the demand to capacity ratio.

Updated on
Your inputs
in

Value out of range

in

Value out of range

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

ksi

Value out of range

ksi

Value out of range

kips

Value out of range

Results

Demand to capacity ratio

0.74

The block shear strength is enough with some margin
Net area in shear
2.79 in²
Net area in tension
0.40 in²
Nominal block shear strength Rn
108.2 kips
Design strength φRn
81.1 kips

The steel block shear calculator gives the net areas, the block shear rupture strength of the AISC 360 and the demand to capacity ratio of a plate or angle with a line of bolts, from the thickness, the bolt layout, the edge distances and the steel grade.

How the calculation works

  • Enter the thickness of the plate, the bolt diameter, the number of bolts, their spacing and the two edge distances.
  • Enter Fy and Fu, choose the tension stress on the block and enter the factored load.
  • The calculator gives the net areas, the block shear strength of the AISC 360 and the demand to capacity ratio.

Example

A plate 0.375 in thick with 4 bolts of 3/4 in at 3 in spacing, an end distance of 1.5 in and an edge distance of 1.5 in (A36 steel, Fy = 36 ksi, Fu = 58 ksi) has a hole of 0.875 in. The net shear area is 0.375 × 7.4375 = 2.79 in² and the net tension area is 0.375 × 1.0625 = 0.40 in². Shear yielding with tension rupture gives 108.2 kips, lower than the 120.2 kips of shear rupture, so Rn = 108.2 kips and φRn = 0.75 × 108.2 = 81.1 kips. For a factored load of 60 kips the ratio is 0.74.

Why it matters

The calculator helps structural engineers, steel detailers, fabricators and students to check the block shear of a gusset plate, a coped beam or an angle in a few seconds, and to see how much the edge distance or the number of bolts changes the strength.

Good to know

Check the block shear when the edge distance is short, when the beam is coped or when the plate is thin compared with the load, since these are the cases where it controls. Use the real hole size of the shop, and the actual Fy and Fu of the mill report if you know them. Remember that the strength grows with the length of the shear plane, so a wider spacing or one more bolt is the quickest way to add capacity, but more edge distance on the tension side adds less.

The bolt shear capacity calculator checks the shear and the bearing of the bolts, the Whitmore gusset width calculator gives the width of the stress zone, the steel tension member calculator checks the member and the slip-critical bolt capacity calculator checks a friction connection.

Frequently asked questions

What is block shear?

Block shear is the tearing out of a block of steel at the end of a connected member. The block is held by a shear failure along the line of bolts and a tension failure across the end, so the bolts and a piece of plate leave together. It governs coped beams, gusset plates, angles and tension members with short edge distances, and it can control the design before the bolts do.

What are the two equations?

The AISC 360 section J4.3 gives the strength as 0.6 Fu Anv + Ubs Fu Ant, with an upper limit of 0.6 Fy Agv + Ubs Fu Ant. In the first equation the shear plane ruptures, in the second it yields. The smaller value governs. The net areas deduct the holes and the gross area is used for yielding of the shear plane. The calculator takes the smaller of the two.

What is the factor Ubs?

Ubs is 1.0 when the tension stress on the block is uniform, as for a single line of bolts, and 0.5 when it is not uniform, as for two or more lines of bolts in a coped beam where the stress is higher at the first line. Use 0.5 when in doubt, because it gives the safer, because smaller, strength. The resistance factor is 0.75 for LRFD.

What does the calculator leave out?

The calculator checks one L-shaped block with a single line of bolts, along the load and across the end. It does not check a U-shaped block with two tension planes, the bolt shear and bearing, the tension yielding or rupture of the member or the weld of a welded connection. Check these with your own tools. The metric version uses the same American equations, and Eurocode 3 has a similar but different method.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.