Skip to content
Omnikalc

Steel wide flange compactness and width-thickness calculator

Enter the flange and web dimensions and the steel to get the slenderness of the flange and the web, their limits and the class in flexure and compression.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

ksi

Value out of range

ksi

Value out of range

Results

Class in flexure (1 compact, 2 noncompact, 3 slender)

2

Noncompact: the flexural strength is reduced by local buckling
Flange slenderness bf / 2tf
10.21
Compact limit for the flange
9.15
Web slenderness h / tw
25.9
Compact limit for the web
90.6
Class in compression (1 nonslender, 2 slender)
1
Nonslender: no reduction of the compression strength

The steel compactness calculator gives the flange and web slenderness, the compact limits and the class of a wide flange section in flexure and in compression (compact, noncompact or slender) according to AISC 360 Table B4.1.

How the calculation works

  • Enter the flange width and thickness, the clear height of the web and its thickness.
  • Enter the yield stress and the modulus of elasticity of the steel.
  • The calculator gives the slenderness of the flange and the web, their limits and the class of the section in flexure and in compression.

Example

A W14×90 in 50 ksi steel has a flange of 14.5 in by 0.71 in and a web of 0.44 in with a clear height of 11.38 in. With √(E/Fy) = 24.08, the flange slenderness is 14.5 / (2 × 0.71) = 10.21, above the compact limit 0.38 × 24.08 = 9.15, so the flange is noncompact and the class in flexure is 2. The web slenderness is 25.9, well below the limit 90.6, so the web is compact. In compression, 10.21 is below 0.56 × 24.08 = 13.5 and 25.9 below 35.9, so the section is nonslender.

Why it matters

The calculator helps structural engineers, steel designers and students to classify a rolled or welded I-shape before they choose the flexural equations, to see how the steel grade changes the limits and to understand why some sections cannot reach the plastic moment.

Good to know

Use the clear web height h between the fillets, not the full depth, and the half-width of the flange. Higher strength steel has lower limits, so a section that is compact in 36 ksi can be noncompact in 65 ksi. For a built-up section, check the plates one by one, and for a hybrid section use the yield stress of each element.

The steel column capacity calculator gives the compressive strength, the steel beam lateral-torsional buckling calculator gives the flexural strength, the web shear buckling calculator gives the shear strength and the plastic moment capacity calculator gives the plastic modulus.

Frequently asked questions

What are the width-thickness ratios?

For a rolled wide flange, the flange slenderness is the half-flange width divided by the thickness, bf / 2tf, and the web slenderness is the clear height divided by the web thickness, h / tw. A plate that is too slender buckles locally before the member reaches its strength, so the codes limit these ratios and reduce the strength when they are exceeded. The limits depend on the stress, through the factor √(E / Fy).

What are the limits in flexure?

AISC 360 Table B4.1b gives, for the flange of a rolled I-shape in flexure, the compact limit 0.38 √(E / Fy) and the noncompact limit 1.0 √(E / Fy). For the web it gives 3.76 √(E / Fy) and 5.70 √(E / Fy). A section whose elements are all below the compact limits is compact and can reach its plastic moment. Over the compact limit it is noncompact, and over the second limit it is slender.

What are the limits in compression?

For a member in axial compression, the flange limit between nonslender and slender is 0.56 √(E / Fy), and the web limit is 1.49 √(E / Fy). If an element is slender, the compressive strength is reduced by the factor Q, found with the effective width of the slender plate. Most rolled wide flanges are nonslender in 50 ksi steel, but the W14 and the W40 shapes in higher grades can be slender.

How do the European classes compare?

The Eurocode 3 classes 1 to 4 use other limits, based on c / t ratios and a factor ε = √(235 / fy), so a section that is compact in the AISC is not always class 1 in the Eurocode. The calculator follows the American method, and uses the same equations in metric units. Check the section with the code of your project before you rely on the class.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.