Skip to content
Omnikalc

Stopping sight distance calculator: distance needed to stop a vehicle before an obstacle

Enter the design speed, the reaction time, the deceleration, the grade and the available sight distance to get the reaction distance, the braking distance, the stopping sight distance and the margin.

Updated on
Your inputs
mph

Value out of range

s

Value out of range

ft/s²

Value out of range

%

Value out of range

ft

Value out of range

Results

Stopping sight distance

492.0 ft

Perception-reaction distance
202.1 ft
Braking distance
289.9 ft
Available sight distance over the stopping distance
1.22
The available sight distance is enough to stop

The stopping sight distance calculator gives the distance needed to stop a vehicle from the design speed, the perception-reaction time, the deceleration and the grade, as the sum of the reaction distance and the braking distance, and compares it with the available sight distance.

How the calculation works

  • Enter the design speed, the perception-reaction time (2.5 s is the AASHTO standard) and the deceleration rate (11.2 ft/s² is the standard value).
  • Enter the grade of the road, with a negative sign for a downhill grade.
  • Enter the sight distance available, for example from a crest vertical curve or a curve with a wall.
  • The calculator adds the reaction distance 1.47 V t and the braking distance V² / (30 (a / 32.2 ± G)) and compares the result with the available sight.

Example

A driver at 55 mph needs a reaction distance of 1.47 × 55 × 2.5 = 202.1 ft. On a level road with a deceleration of 11.2 ft/s², the braking distance is 55² / (30 × (11.2 / 32.2)) = 289.9 ft. The stopping sight distance is 492.0 ft. If the road gives 600 ft of sight, the ratio is 600 / 492.0 = 1.22, so the sight distance is enough.

Why it matters

The calculator helps road designers, traffic engineers, surveyors and students to check the sight distance of a road, a driveway or an intersection, to size crest curves and to set safe speeds. It also helps to understand why speeding increases the distance needed to stop with the square of the speed.

Good to know

Measure the available sight distance from the driver’s eye height of 3.5 ft (1.08 m) to an object height of 2 ft (0.6 m) on the road. Use the AASHTO values for design, and larger values on downhill grades. For a safety study of a particular road, consider the conditions such as rain, ice or heavy trucks, which need more distance. The design must follow the standards of your road authority.

The vertical curve calculator sizes curves for sight distance, the horizontal curve calculator covers curve geometry, the minimum curve radius calculator gives the radius for a design speed and the spiral curve length calculator covers transition curves.

Frequently asked questions

What is stopping sight distance?

The stopping sight distance is the length of road a driver needs to see ahead to perceive an obstacle, react and brake to a full stop before reaching it. It is the minimum sight distance that any road must provide at every point. It is used to design crest vertical curves, horizontal curves with obstructions on the inside and the placement of signs and barriers.

What values are used for the reaction time and the deceleration?

AASHTO uses a perception-reaction time of 2.5 seconds, which covers the large majority of drivers, and a deceleration of 11.2 ft/s² (3.4 m/s²), which most drivers can keep in an emergency stop on wet pavement without losing control. These values are for the design of roads. A particular driver may need more time, especially when tired, old or surprised.

How does the grade change the distance?

On a downhill grade the vehicle needs a longer distance to stop because the gravity pushes it forward, and the braking distance is longer. On an uphill grade the distance is shorter. The formula includes the grade G as a decimal in the denominator: a 6% downhill grade reduces the effective deceleration by 0.06 g, or about one sixth for the standard value. Long steep downhill grades add the risk of brake fade for heavy trucks.

What is the difference with the decision sight distance?

The decision sight distance is longer, and it is used where drivers must make complex decisions, as at an interchange, a toll plaza or a lane drop, where the information must be found, interpreted and acted on. It includes a pre-maneuver time of 3 to 14 seconds. The stopping sight distance is the minimum for a simple stop.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.