Skip to content
Omnikalc

Deep beam strut-and-tie model tie force and steel calculator

Enter the point load, the span, the depth, the lever arm, the yield strength and the bar area to get the shear span, the tie force, the strut force, the steel and the number of bars.

Updated on
Your inputs
kip

Value out of range

ft

Value out of range

ft

Value out of range

Value out of range

ksi

Value out of range

in²

Value out of range

Results

Steel required for the tie

8.33 in²

Shear span
6.0 ft
Lever arm
4.80 ft
Tie force
375.0 kip
Strut force
480.2 kip
Number of bars
11

The deep beam strut-and-tie model tie force and steel calculator gives the shear span, the lever arm, the tie force, the strut force, the steel required for the tie and the number of bars of a deep beam with a point load at midspan, from the load, the span, the depth and the yield strength.

How the calculation works

  • Enter the point load, the span and the depth of the deep beam.
  • Enter the lever arm as a part of the depth, the yield strength and the area of one bar.
  • The calculator finds the shear span, the tie force, the strut force, the steel required and the number of bars.

Example

A deep beam of 12 ft span and 6 ft depth carries 600 kip at midspan. The shear span is 6.0 ft and the lever arm is 0.8 × 6 = 4.80 ft. The tie force is 300 × 6.0 / 4.8 = 375.0 kip, and the strut force is 300 × √(6² + 4.8²) / 4.8 = 480.2 kip. With 0.75 × 60 ksi, the steel is 8.33 in², that is 11 bars of 0.79 in².

Why it matters

The calculator helps structural engineers, students and checkers to understand the strut-and-tie method, to get a first estimate of the tie of a transfer girder or a deep beam, and to compare the effect of the depth and of the lever arm on the steel.

Good to know

Draw the strut-and-tie model with the real width of the struts and the size of the bearing plates, and check the nodal zones and the struts. Anchor the tie bars well beyond the supports, with hooks or with plates, and place the web reinforcement in both directions. Do not use the lever arm of a normal beam for a deep beam without checking the model.

The RC beam flexural capacity calculator gives the bending capacity of a normal beam, the punching shear calculator checks a slab at a column, the beam bearing length calculator checks a support and the rebar development length calculator gives the anchorage of the bars.

Frequently asked questions

What is a deep beam?

A deep beam is a beam whose depth is large compared with its span, as a transfer girder or a wall over an opening. In the ACI 318, a beam with a clear span of less than four times its depth, or with a load near the support, is a deep beam. The plane sections do not stay plane in it, so the usual bending theory is not valid and a strut-and-tie model is used.

How does the strut-and-tie model work?

The strut-and-tie model replaces the beam by a truss. The concrete forms compression struts, the steel forms the tension ties, and the nodes connect them. For a point load at midspan, two inclined struts go from the load to the supports, and a horizontal tie at the bottom holds the supports apart. The forces are found by the equilibrium of the nodes.

How is the steel found?

The tie force is the half of the load times the shear span divided by the lever arm. The area of the steel is the tie force divided by the strength reduction factor, 0.75 in the ACI 318 for the strut-and-tie models, times the yield strength. The bars must be anchored in the nodal zones beyond the supports, and they must be distributed on the width of the tie.

What are the limits of the calculator?

The calculator solves the simple truss with one point load at midspan and a lever arm that you give. It does not check the strength of the struts and of the nodal zones, the bearing at the supports and under the load, the minimum web reinforcement, the anchorage of the tie, or the other load cases. A deep beam must be designed with all the checks of the standard.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.