Skip to content
Omnikalc

Threaded hanger rod trapeze load and size calculator

Enter the number of pipes, their weight, the hanger spacing, the length of the run and the rod diameter to get the load on a trapeze, the stress in the rods, the ratio and the number of hangers.

Updated on
Your inputs

Value out of range

lb/ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Ratio of the stress to 12 ksi

0.84

The rods are within the usual allowable stress
Weight per foot of the run
160 lb/ft
Load on one trapeze
1,600 lb
Load on one rod
800 lb
Root area of the rod
0.0798 in²
Stress in the rod
10.03 ksi
Number of hangers
13

The threaded hanger rod trapeze load and size calculator gives the weight per foot of the run, the load on a trapeze, the load on a rod, the stress in the rod, the ratio to the allowable stress and the number of hangers for a pipe run hung on trapezes.

How the calculation works

  • Enter the number of pipes on the trapeze and the weight of one pipe with its contents.
  • Enter the spacing of the hangers, the length of the run and the diameter of the rods.
  • The calculator finds the load on a trapeze, the load on a rod, the rod stress, the ratio and the number of hangers.

Example

A trapeze carries 4 pipes of 40 lb/ft, that is 160 lb/ft. With hangers every 10 ft, the load on a trapeze is 1,600 lb, and 800 lb on each of the two rods. A 3/8 in rod has a root area of 0.7854 × (0.85 × 0.375)² = 0.0798 in², so the stress is 10.03 ksi, a ratio of 0.84 to 12 ksi. A run of 120 ft needs 13 hangers.

Why it matters

The calculator helps mechanical and plumbing contractors, pipefitters, estimators and students to select the size of the hanger rods for a group of pipes, to count the hangers of a run, and to see the effect of the spacing on the load.

Good to know

Use the weight of the pipes full of water, with the insulation and the valves, and add a margin for the test. Center the group of pipes on the trapeze, and anchor the rods to the structure with approved anchors. Brace the long rods and use a rod stiffener if the rod is long, and do not hang a pipe from another pipe.

The pipe support spacing calculator gives the spacing of the hangers, the pipe expansion loop calculator sizes a loop for the thermal movement, the wire rope capacity calculator gives the strength of a rope and the anchor bolt pullout calculator checks an anchor in concrete.

Frequently asked questions

What is a trapeze hanger?

A trapeze hanger is a horizontal support, often a steel channel, hung from the structure by two threaded rods. It carries several pipes, conduits or ducts side by side. The trapeze is used where a group of pipes runs in the same direction, as in a mechanical room or a ceiling space, and it needs less rods and anchors than separate hangers.

How is the load on the rods found?

The load on a trapeze is the weight per foot of all the pipes, with the water and the insulation, times the spacing of the hangers. The two rods share the load equally if the pipes are centered. If the load is not centered, one rod carries more. The weight of the trapeze and the extra load of the test must be added.

How is the rod size selected?

The stress in the rod is the load divided by its root area at the thread. The allowable stress used by the standard of the hangers is about 12 ksi (83 MPa) for the usual carbon steel rods, which includes a safety factor. The table gives the maximum load for each size: about 610 lb for a 3/8 in rod, 1,130 lb for 1/2 in and 1,810 lb for 5/8 in.

What are the limits of the calculator?

The calculator checks the tension in the rods with an approximate root area. It does not check the bending of the trapeze, the anchor in the structure, the buckling of a long rod under a compression, the seismic bracing, the thermal movement of the pipes or the fatigue. The hangers must follow the standard of the pipe supports and the rules of the project.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.