Skip to content
Omnikalc

Eccentrically loaded weld group calculator

Enter the load, the eccentricity, the weld length, the spacing and the electrode to get the moment, the resultant force and the weld size for two vertical fillet welds.

Updated on
Your inputs
kips

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

Results

Weld size to use

5 /16 in

Moment on the weld group
200.0 kip-in
Polar moment of inertia of the welds
149.3 in³
Resultant force at the critical point
6.833 kips/in
Weld size needed
4.91 /16 in

The eccentric weld group calculator gives the resultant force at the critical point of two vertical fillet welds loaded off-center, and the weld size needed with the elastic method.

How the calculation works

  • Enter the load, its eccentricity from the center of the weld group, the length of each of the two vertical welds and the distance between them.
  • Choose the electrode strength.
  • The calculator gives the moment, the polar moment of inertia, the resultant force at the end of the weld and the weld size needed.

Example

A bracket carries 25 kips at 8 in from two vertical fillet welds of 8 in each, 4 in apart, with E70 electrodes. The moment is M = 200 kip-in and Ip = L³/6 + L b²/2 = 149.3 in³. At the end of a weld, the vertical force is 4.241 kips/in and the horizontal force is 5.357 kips/in, a resultant of 6.833 kips/in. A weld of 1/16 in has a design strength of 1.392 kips/in, so the weld size needed is 4.91/16 in, which rounds to 5/16 in.

Why it matters

The calculator helps steel detailers, engineers, fabricators and students to size the welds of a bracket, a corbel or a seat, to see how the eccentricity increases the force in the weld, and to choose the weld size before checking the base metal.

Good to know

Measure the eccentricity from the center of the weld group, not from the face of the support, and use the factored load. Because the elastic method is conservative, it gives a larger weld than the ultimate strength method, which is acceptable for most brackets. Check that the size you choose is not smaller than the minimum size for the thickest part, and not larger than the maximum for the thinnest part. Check the strength of the base metal along the weld, and remember that the weld must be made on both sides of the joint in the way assumed. A longer weld or a wider spacing reduces the weld size faster than a larger leg.

The fillet weld strength calculator gives the capacity of a straight weld, the weld metal volume calculator gives the electrodes needed, the weld preheat calculator gives the temperature for the steel, and the bolt circle calculator lays out the holes of a flange.

Frequently asked questions

What is the elastic method?

The elastic method treats the weld as a line with a unit throat and splits the load into a direct shear, spread evenly over the welds, and a twist about the center of the group caused by the eccentricity. At each point, the two effects are added as vectors, and the point with the largest resultant sets the size of the weld.

Where is the critical point?

For two vertical welds with a vertical load, the critical point is at the top or bottom end of the weld on the side of the load, where the twist gives the largest horizontal and vertical components. The calculator uses that point, with horizontal distance b/2 and vertical distance L/2 from the center of the group.

What is the strength of a fillet weld?

In AISC 360, the design strength of a fillet weld per inch is 0.75 × 0.6 FEXX × 0.707 w, where w is the leg size. For E70, this is 1.392 kips per inch for each sixteenth of an inch of the leg. In Eurocode 3, the design shear strength of the throat is fu / (√3 βw γM2).

What does the calculator leave out?

The calculator leaves out the strength of the base metal, the minimum and maximum weld sizes, the effect of the load direction on the strength of the weld, the ultimate strength method with its higher capacity, and groups with other shapes. Use the instantaneous center of rotation method for a more economical result.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.