Skip to content
Omnikalc

Headphone power calculator: can your amplifier drive your headphones?

Enter the sensitivity, the impedance, the target level and the amplifier power to get the power, voltage and current needed and the headroom.

Updated on
Your inputs
dB SPL/mW

Value out of range

Ω

Value out of range

dB SPL

Value out of range

mW

Value out of range

Results

Power needed

3.162 mW

Voltage needed (RMS)
0.318 V
Current needed
9.94 mA
Maximum level from the amplifier
114.8 dB SPL
Headroom above the target
9.8 dB
The amplifier has enough power

Headphones differ widely in how much power they need, and a weak source can run out of headroom. This headphone power calculator takes the sensitivity, the impedance, the target peak level and the amplifier power to give the power, voltage and current needed, the maximum level the amplifier can reach and the headroom.

How the calculation works

  • Power needed P = 10^((target level − sensitivity) ÷ 10) in milliwatts, since the sensitivity is the level given by 1 mW.
  • Voltage V = √(P × Z) and current I = √(P ÷ Z), with the power in watts and the impedance Z in ohms.
  • Maximum level = sensitivity + 10 × log10(amplifier power in mW). Each doubling of power adds 3 dB.
  • Headroom = maximum level − target level. It should be positive, and a few dB of margin help with peaks.

Example

A headphone has a sensitivity of 100 dB SPL/mW and an impedance of 32 Ω. To reach peaks of 105 dB it needs 10^(5 ÷ 10) = 3.16 mW, which is 0.318 V and 9.94 mA. An amplifier of 30 mW into 32 Ω can reach 100 + 10 × log10(30) = 114.8 dB, so the headroom is 9.8 dB.

Why it matters

Audio fans, musicians and engineers use the figures to match headphones with a phone, a DAC or an amplifier before buying. The calculation shows quickly if a high-impedance headphone will sound weak from a portable source.

Good to know

The calculation treats the headphone as a constant impedance, which it is not, since impedance changes with frequency, and the amplifier power depends on the load. Manufacturers measure sensitivity in different ways, and some give it per volt. Real music has peaks and a spectrum that vary a lot. The result is for matching equipment and is not a guide to a safe listening level.

The noise exposure calculator looks at safe listening time, the dBm converter converts between power levels and the acoustic impedance calculator covers sound in media.

Frequently asked questions

What does sensitivity mean?

Sensitivity tells how loud a headphone is for a given input. When it is given in dB SPL per milliwatt, a value of 100 means that 1 mW produces a level of 100 dB. A higher number means a louder headphone with the same power. Some makers give the sensitivity per volt, which is a different figure.

Why does impedance matter?

For a given voltage, a lower impedance draws more current and power, and a higher one less. A phone that gives a small voltage drives a low-impedance headphone more easily, while a high-impedance headphone often needs an amplifier that gives a larger voltage. Power depends on both voltage and impedance.

How much power do I need?

Typical listening levels are well below the peak levels that music can reach. Peaks of 100 to 110 dB need a few milliwatts for a sensitive headphone, and tens of milliwatts or more for an insensitive one. Dynamic music may need about 20 dB of headroom above the average level.

Is louder safer or better?

No. Long exposure to levels above about 85 dB can damage hearing, and the safe time falls quickly as the level rises. This calculator is for planning an amplifier, and not for setting a listening level. Keep the volume at a level that is comfortable and safe.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.